Diagnostic information
2-35
7510
Go Back
Previous
Next
986.00
Service finisher
error
Sensor (media eject clamp
HP) late error
The sensing area of the sensor (media eject clamp
HP) is not interrupted within the specified time after
the eject clamp starts moving to the home position.
Refer to the
Finisher Service Manual.
986.01
Service finisher
error
Sensor (media eject clamp
HP) lag error
The sensing area of the sensor (media eject clamp
HP) remains interrupted within the specified time
after the eject clamp starts moving from the home
position.
Refer to the
Finisher Service Manual.
987.00
Service finisher
error
Sensor (media eject shaft
HP) late error
The sensing area of the sensor (media eject shaft
HP) is not interrupted within the specified time after
the media eject shaft starts moving to the home
position.
Refer to the
Finisher Service Manual.
987.01
Service finisher
error
Sensor (media eject shaft
HP) lag error
The sensing area of the sensor (media eject shaft
HP) remains interrupted within the specified time
after the media eject shaft starts moving from the
home position.
Refer to the
Finisher Service Manual.
988.01
Service finisher
error
Sensor (punch unit side
reg 1) lag error
Sensor (punch unit side
reg 2) lag error
The sensor (punch unit side reg 1) or sensor (punch
unit side reg 2) did not detect any media correctly.
Refer to the
Finisher Service Manual.
989.00
Service finisher
error
Stapler unit error
The sensing area of the sensor (stapler unit motor
HP) inside the stapler unit assembly is not
interrupted within the specified timer after the
stapler unit motor starts moving to the home
position.
Refer to the
Finisher Service Manual.
990.00
Service finisher
error
Sensor (stapler carriage HP)
late error
The sensing area of the sensor (stapler carriage
HP) is not interrupted within the specified time after
the stapler carriage starts moving to the home
position.
Refer to the
Finisher Service Manual.
990.01
Service finisher
error
Sensor (stapler carriage HP)
lag error
The sensing area of the sensor (stapler carriage
HP) remains interrupted within the specified time
after the stapler carriage starts moving from the
home position.
Refer to the
Finisher Service Manual.
991.00
Service finisher
error
Sensor (booklet front tamper
HP) late error
The sensing area of the sensor (booklet front
tamper HP) is not interrupted within the specified
time after the front booklet tamper starts moving to
the home position.
Refer to the
Finisher Service Manual.
991.01
Service finisher
error
Sensor (booklet front tamper
HP) lag error
The sensing area of the sensor (booklet front
tamper HP) remains interrupted within the specified
time after the front booklet tamper starts moving
from the home position.
Refer to the
Finisher Service Manual.
Error code or
message
Error contents
Description/Action
Summary of Contents for X945E
