3-28
Service Manual
7510
Go Back
Previous
Next
Press
Stop
to return to ENGINE ADJUST.
PRO-CON (ATC sensor setup and adjust)
This procedure is used to adjust the following:
Sensor (C ATC)
Sensor (M ATC)
Sensor (Y ATC)
Sensor (K ATC)
Select
PRO-CON
and select:
Then Select:
Appears on the LCD
ATC Sensor Adjust values
(
Sen Grad SNR-Y
Registration values appear on the LCD. If
required, reset the values and
Select
to submit
the changes.
Sen Grad SNR-M
Registration values appear on the LCD. If
required, reset the values and
Select
to submit
the changes.
Sen Grad SNR-C
Registration values appear on the LCD. If
required, reset the values and
Select
to submit
the changes.
Sen Grad SNR-K
Registration values appear on the LCD. If
required, reset the values and
Select
to submit
the changes.
SNR Output Ref TC-Y
Registration values appear on the LCD. If
required, reset the values and
Select
to submit
the changes.
SNR Output Ref TC-M
Registration values appear on the LCD. If
required, reset the values and
Select
to submit
the changes.
SNR Output Ref TC-C
Registration values appear on the LCD. If
required, reset the values and
Select
to submit
the changes.
SNR Output Ref TC-K
Registration values appear on the LCD. If
required, reset the values and
Select
to submit
the changes.
ATC Sensor Adjust Cycle
Testing... Pass
RegCon (color registration)
This procedure is used to adjust the printhead color registration.
Select
RegCon Adjust
and then select:
Appears on the LCD:
Measurement Cycle
Reg Measuring Testing...
Control Sensor Check
Reg Control Sensor Testing...
Control Sensor Cycle
Reg Control Sensor Correction Testing...
Belt Edge Learn
Belt Edge Learn Testing...
Select
RegCon Adjust
and then select:
Then select:
Appears on the LCD:
Control Setup Cycles
Skew Fine Setup
Skew Fine Setup Testing...
IN/OUT Setup
IN/OUT Setup Testing...
Center Setup
Center Setup Testing...
Skew Rough Setup
Skew Rough Setup Testing...
Cycle Result Value
Cycle Result Values appear on the LCD.
Summary of Contents for X945E
