Diagnostic aids
3-29
7510
Go Back
Previous
Next
Color registration (RegCon)
The purpose of the color registration is to establish correct horizontal and vertical positioning of the four primary
color images.
The procedure consists of the following steps, which must be performed in the listed sequence:
1.
Belt Edge Learn
- Used to align the transfer belt positioning system.
2.
Fine Skew Setup
- Automatically performs horizontal and vertical alignment, and reports any skew in the
various images caused by the printhead misalignment. The skew must be corrected through manual
adjustment.
3.
In/Out Setup
- Automatically performs magnification adjustment so that scan lines are the same length for
all four colors. Also checks for skew.
4.
Center Setup
- Aligns the midpoints of scan lines for all colors, for magnification balance. There is also a
Rough Skew Setup
when skew is outside the measurement parameters of the
Fine Skew Test
.
Booklet Fold Adjust
To perform the Booklet Fold Adjust Test:
1.
Select
Booklet Fold Adjust
from the Diagnostics Menu.
The following tests appear on the LCD
Finisher Config
To perform Finisher Config:
1.
Select
Finisher Config
from the Diagnostics Menu.
Finisher Config values appear on the LCD. If required, reset the values and submit
Select the following:
Appears on the LCD:
Booklet Tamper Shift Adjust
Booklet Staple Fold Fine Adjust values appear on the
LCD. If required, reset the values and submit.
Booklet Compile position
Booklet Compile position values appear on the LCD. If
required, reset the values and submit.
Booklet 2-sheet
Booklet 2-sheet values appear on the LCD. If required
reset the values and submit.
Booklet 15-sheet
Booklet 15-sheet values appear on the LCD. If required
reset the values and submit.
Booklet Fold Pos Fine Adj
Booklet Staple Fold Fine Adjust values appear on the
LCD. If required, reset the values and submit.
Booklet Staple Pos Fine Adj
Booklet Staple Fold Fine Adjust values appear on the
LCD. If required, reset the values and submit.
Summary of Contents for X945E
