background image

________________________________________________________

Spa Specifications

  

 

ELECTRICAL AND PEDICURE SPA COMPONENT 
SPECIFICATIONS

 

 

All electrical connections MUST be made by a qualified, licensed electrician in accordance with Local & National 
Electrical and Building Codes. A 110V-50/60 Hz, 15 Amp, GFCI protected grounded circuit MUST be used to 
supply power to the Pedicure Spa. A dedicated circuit must be used with a GFCI. All wiring must conform to 
National & Local Electrical Codes

 

WARNING:

 

IT IS EXTREMELY IMPORTANT THAT THE FOOT SPA OPERATES WITH GFCI  PROTECTION

 

 

 

VERY IMPORTANT Both back of chair and seat are adjustable. When both are at maximum positions one must 
allow 18” (44cm) from back wall to foot spa. This minimum distance assures unobstructed recline. Failure to 
follow this required dimension might damage your spa components and plumbing connections, which will void 
your warranty. 

 

PEDICURE SPA SPECIFICATIONS: 

 

Construction: Marble composite, high gloss, acetone-proof gel coat. 

 

Two (2) electro-mechanical knobs control the drain and whirlpool. 

 

Electro-mechanically operated reclining, massaging, and sliding seat with hand held control. 

 

One (1) pipe-less whirlpool jet. (Pipe-free technology) 

 

Power drain or Gravity drain   

 

Extendable water spray positioned well above water line, air gap is accommodated with back-flow 
prevention required by plumbing code 

 

Depending on pedicure spa model, arms may swing open, swing up / down or slide forward / backward.

 

 

 

SPECIFICATIONS 

  

Spa Dimensions & Weights 
 
 
 
 
 
Adjustable Stool 

   L

 52”(132cm),   W=31”(79cm) w/ Tray 47" (120cm)  H=56”(142cm)  

  *Spa Fully Recline: 68” (172cm)  
   Empty Weight:             ~ 200 lbs.  
   Shipping Weight:         ~ 260 lbs.     
   Max. Handling Weight ~ 250lbs 
   Pedicure Stool: 12” – 13”.  Manicure Stool: 16.25” – 20”  

Spa Water Capacity 

 ~ 4.5 US Gallon 

Jet Motor 

   120 VAC. at 85W 60Hz  

Massage Motors,  
Seat Sliding & Reclining 

   24VDC, 2.5A x 5 

Discharge Pump 

 
   Motor – 120V at 85W 60 Hz    Maximum vertical lift: 3ft.   Flow rate 500 GPH @  floor level 

Power source 

   115 VAC, 60HZ,   Power needed per spa chair = 6 Amp  

Electrical Switches 

   One (1) electro-mechanical knob for the Whirlpool. Rated at 5A contact. 
   One (1) electro-mechanical knob for the Drain. Rated at 5A contact. 

Plug & Play Installation 

   Installation should be made with connection at the external interface parts.  
   Please consult with your local plumber. 

Safety 

 
   Versas® Pedicure Spa is UL listed. 
 

 
 

 

11 

Summary of Contents for VERSAS



















Reviews: