COMMER
CIAL MODE
53
Learn Setup from Master 20LH1DC1
Press 1 to select the “LEARN FROM TV” option, then press
ON/OFF, POWER, or ENTER to go to the Memory Bank
Selection Menu. Pick the Memory ”Bank” you want to store
the master 20LH1DC1’s setup in by pressing either Channel
button repeatedly to choose Memory 1, 2 or 3. (If you
choose a Memory “Bank” that has a master device’s setup
programmed into it, that setup will be overwritten by the new
master 20LH1DC1’s setup.) Once the Clone memory bank is
selected, press ON/OFF, POWER, or ENTER. The Clone
memory bank you have selected will be shown. Press ON/OFF
or POWER to begin copying the master 20LH1DC1’s setup.
CLONE PROGRAMMER/LEARNING SETUP
- Instructions for the Clone Programmer to Learn the Master 20LH1DC1 Setup.
Learning the Master TV Setup
Use MPI Cable to Connect LT2002 Clone Programmer to
Master 20LH1DC1 MPI Port
If there is a good connection, “THE CLONE HAS CONTROL
OF TV” message will appear. Press any button on the
Installer remote.
Set the Clock (Optional)
Set the time on a Master TV’s Clock. (If the time has
already been copied from a TV into the Clone programmer,
you can set a master TV’s clock by copying the time from
the Clone programmer.) The Clone Programmer can copy the
current time to both a master TV and to the Clone’s internal
clock; accurate to within one minute. (Another reason that
the Clone programmer should be equipped with fresh,
high-quality alkaline batteries, is for it to keep the time as
accurately as possible.)
Since the Clone Programmer’s time cannot be set directly,
the current time needs to be copied from a LG TV equipped
with M.P.I. input capability.
After the time is copied to the Clone programmer, the
current time can then be transferred to another TV. (This
can be a master TV, or another TV which has already had
the features set up.)
*Note: When using the clone programmer for teaching or learning,
be sure that the heartbeat pattern is shown on the LEDs. Both learning
and teaching should take about 45 or more seconds depending on the
complexity of the master setup. While the clone is functioning, do not
move it or otherwise disturb the clone or wiring connections. If the clone
finishes the function in less than 45 seconds, redo the function again.
Press the reset button if the clone does not act normally.
LT2002 Clone Programmer Communication
Problems
• A slow flashing green light indicates there are
communication problems between the
20LH1DC1 and the LT2002 clone
programmer. If this is the case, check for a
damaged cable, poor contacts, or other
connection troubles.
• If the status indicator is red, the programmer
batteries are low and should be replaced. Install
4 high-quality alkaline AA batteries.
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION
XX
THE TV IS VERSION
XX
THE SW IS REVISION
XX
CLONE CLOCK=
XX:XX
TV CLOCK=
XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
This menu should appear by itself after the
LT2002 is connected to the 20LH1DC1 MPI port.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
- TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
- TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER
Summary of Contents for 20LH1DC1
Page 70: ...APPENDIX 70 APPENDIX CLONE TROUBLESHOOTING FLOW CHART ...
Page 71: ...APPENDIX 71 TV OPERATING CHECK ...
Page 74: ...74 NOTE ...
Page 76: ......
