background image

SAFETY PRECAUTIONS

• 

If you are a professional installer, please read this manual carefully before installing the product.

• 

If you are a professional installer, please hand this manual to the user after installation. Please ensure that 
the user also reads the manual carefully and retains it for future reference.

After reading the installation manual, please keep it nearby for future reference.

Precautions When Installing the Product 

 WARNING

• 

The product should be installed by a professional installer specified by the retail store.

 

- Product installation by a non-professional installer is very dangerous and may cause personal injury.

• 

The product should be installed where its weight can be fully supported.

 

- If the product is installed on a weak surface, the product may fall, causing injury.

• 

When moving or replacing the product after installation, contact a professional installer specified by the 
retail store.

 

- Installation or movement of the product must be carried out by a skilled professional. If an unqualified 

person moves or installs the product, it may cause safety risks.

• 

Do not hang on this product or strike it in any way. 

 

- The product may fall and cause injury.

• 

Do not grab the product or expose it to impact while in operation.

 

- This may damage or break the motor.

 CAUTION

• 

Follow the instructions in the installation manual to properly install this product. 

 

- Failure to follow the instructions in the installation manual could lead to improper installation and result 

in serious injury or product damage.

• 

Four or more people are required to install or adjust the height of the product.

 

- If you try to install or move the product alone, it may fall, causing injury or damage to the product.

• 

Before installation, confirm that the ceiling is made of material that is strong enough to hold the product, 
and use the anchors and screws provided. 

 

- If you use anchors and screws that are not specified by the manufacturer, they may not hold the weight 

of the product, causing safety issues.

• 

When drilling holes into the ceiling, make sure you use a drill and drill bit with the specified diameter. 
Ensure that you also follow the instructions regarding the depth of the holes. 

 

- Otherwise, the product may be installed incorrectly and cause safety issues.

• 

Do not clean the product with a wet towel, and do not place a heater or humidifier beneath it. 

 

- Moisture permeating into the product, including from steam and heat, may result in a fire, electric shock 

or damage to the product.

• 

Keep this product away from sprinklers, sensors, high-tension wires and power sources. Do not install it in 
a location where vibrations or impacts are likely to occur.

3

2

ENG

ENGLISH

ENG

ENGLISH

Summary of Contents for ACC-CR-EH5C

























Reviews: