background image

04

Do not touch the glass surface or 

frame of the solar module after 

installation of the module. It may 

result in injury or death.

Heavy objects must be kept off of 

the solar module.

Do not stand on or step on the 

module. Do not drop the module. 

Failure to comply may result in 

product damage, product failure 

or bodily injury. 

Do not scratch the coating 

surface of the frame. 

Scratches may decrease the total 

solar output due to corrosion of 

the frame.

sunlight on the solar module 

Do not artificially concentrate

surface. Failure to comply may 

result in product damage or 

failure.

Do not apply a shock to the 

junction box of the module or 

pull the cable. Do not remove the 

labels attached to the module. 

Failure to comply may result in 

damage of the product.

If the installing modules on curved surface, (e. g. arch 

type), as shown in the below picture, do not forcefully 

modify the module in the installation when connecting 

it with the structure. Only install the module in the place 

where the structure for the panels  has been properly 

set up. An improper structure may cause deformation 

of the panels. Panels may also be damaged by 

unapproved installation methods such as the use of a 

crane.

Module

Installing structure
(bent type)

Module

Installing structure
(Stralght type)

Product

Deformation

Occurrence

of space

Partial shadow must be removed 

from solar module because it can 

cause severe problems of solar

module.

Summary of Contents for LG N1K-N6 Series




















Reviews: