background image

ENGLISH

3

IMPORTANT SAFETY INSTRUCTIONS

 

If you are a professional installer, please read this manual carefully before installing the product.

 

If you are a professional installer, please give this manual to the user after installing the product and ensure that the 

user also reads the manual carefully and retains it for future reference.

After reading the manual, please keep it handy for future reference.

 WARNING

 

The product should be installed by a qualified professional specified by the retail store.

 - Product installation by non-qualified personnel is very dangerous and may cause personal injury.

 

The product should be installed where its weight can be fully supported.

 - If the product is installed on a weak surface, the product may fall, causing injury.

 

When moving or replacing the product after installation, contact a qualified installer specified by the retail store.

 - Installation or movement of the product must be carried out by a skilled professional. If an unqualified person moves 

and installs the product, it may cause safety risks.

 

Do not hang on this product, protect the product from severe impacts after the installation.

 - The product may fall and cause injury.

 

Be sure not to hang the power cable and signal cable on the back of TV when installing the wall-mounted TV.

 - Damaged cables may result in fire, electric shock, or damage to the product.

 CAUTION

 

Follow the instructions in this manual to properly protect the product. 

 - If you do not follow these instructions, the product may be installed incorrectly and cause serious injury or the 

product may become damaged.

 

To install or adjust the height of the product, two or more people are needed.

 - If you try to install or move the product alone, it may fall and cause injury or the product may become damaged.

 

When installing the product, first check that the wall is strong enough. Use the anchors and screws provided.

 - If you use anchors and screws that are not specified by the manufacturer, they may not hold the weight of the 

product, causing safety issues.

 

When drilling holes into the wall, make sure you use a drill and drill bit with the specified diameter. Ensure that you 

also follow the instructions regarding the depth of the holes.

 - Otherwise, the product may be installed incorrectly and cause safety issues.

 

Do not clean the product with a wet towel, and do not place a heater, or humidifier beneath it.

 - Moisture, steam or heat permeating into this product may result in fire, electric shock or product damage.

 

Keep this product away from sprinklers, sensors, high-tension wires and power sources. Do not install it in a location 

where vibrations or impacts are likely to occur.

 

Make sure that the power cord is removed from the outlet before installing the product.

 - Otherwise, it may cause an electric shock or fire.

 

Wear safety gloves when installing the product. Do not use your bare hands.

 - Otherwise, it may cause personal injury.

 

Be sure to use the accessory cable provided. Otherwise, friction between the product and the wall may cause damage 

to the connector. (Depending on model)

Summary of Contents for OTW630B















Reviews: