background image

Troubleshooting

39

Troubleshoo

ting

4

Symptoms

Cause & Solution

When you feel the output 

sound of the unit is low.

Check the details below and adjust the unit according to them.

 

y

With the sound bar connected with TV, change the AUDIO DIGITAL OUT 
setting on TV Setup Menu from [PCM] to [AUTO] or [BITSTREAM].

 

y

With the sound bar connected with Player, change the AUDIO DIGITAL OUT 
setting on Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or 
[BITSTREAM].

 

y

Change Audio DRC setting on connected device setup menu to [OFF] state.

 

y

Make sure Night time mode is not On. Turn [OFF] Night time mode.

USB is not recognized.

 

y

Format the USB device and connect it again. 

 

When formatting the USB device, select the available file system. (Page 28)

NOTES to use wireless

Symptoms

Cause & Solution

This device may have 

wireless interference.

 

y

Wireless may not operate normally in weak signal area.

 

y

Please install the device close enough to wireless subwoofer.

 

y

Do not install the device on metal furniture for optimum performance.

Bluetooth

 device may 

malfunction or make 

noise in the following 

cases.

 

y

When any part of your body contact the transceiver of the 

Bluetooth

 device 

or sound bar.

 

y

When there is an obstacle or wall or the device is installed in a secluded spot.

 

y

When there is a device (a wireless LAN, a medical equipment or a microwave) 
using same frequency, make the distance between the products as far away 
as possible each other. 

 

y

When connecting the device to the 

Bluetooth

 device, make the distance 

between the products as close as possible each other.

 

y

When the device gets too far from the 

Bluetooth

 device, the connection is 

disconnected and also malfunction may occur.

Summary of Contents for SN5Y














































Reviews: