background image

17

 

Close the lid

Finish

Caution & Note

• Tub will rotate more than

once without water (While
Water Level LED blinking) to
recognize Water Level.

• Then the Water Level and the

amount of Detergent to be
used will be shown and water
will be supplied.

• Water will be supplied.

After supplying, laun-
dering will 
be started.

• When the wash Course

ends, the buzzer will
ring for 10 seconds
before the Power goes
off automatically.

• If water is already in the tub, or putting wet laundry into the

tub before starting will increase the Water Level.

• With lightweight bulky loads, Water Level can be set low. 

5

4

6

6

5

7

6

5

7

6

5

7

6

5

7

• During water supplying, water supply valve might repeat

on/off to meet adequate temperature for laundry.

Whitening course use more warm water than other course 

as it has higher set temperature for heating.

Stains that easily removed at 40°C:  coffee, cola, orange 

juice, grape juice, soy sauce etc.

• While heating, laundry tub will rotate to a direction slowly. 

This is a part of normal operation.

• While heating, because of humidity difference, there might 

be water drops at the glass of door. This is normal 
phenomenon. Just wipe it after laundry.

• Please be attention that exterior of the machine is hot by 

heating. 

• During water supplying, water supply valve might repeat

on/off to meet adequate temperature for laundry.

Allergy Care course use more warm water than other course 
as it has higher set temperature for heating.

Stains that easily removed at 60°C:  milk, blood, sebum, 
egg, animal and vegetable oil.

• While heating, laundry tub will rotate to a direction slowly.

This is a part of normal operation.

• While heating, because of humidity difference, there might 

be water drops at the glass of door. This is normal 
phenomenon. Just wipe it after laundry.

• Please be attention that exterior of the machine is hot by 

heating.

• Selecting the Allergy Care course automatically incorporates

steam into the wash cycle.

• The Allergy Care course can reduce allergens in bedding and

clothing.

• Due to the higher energy and temperatures used, the Allergy

Care course is not recommended for wool, silk, leather, or 
any other delicate or temperature sensitive items.

• Water supply and drain is executed during rinse and this is a

part of normal operation.

Summary of Contents for WF-S150V













































Reviews: