background image

10

INSTALLATION

Installation Place 

Requirements

Before installing the appliance, check the following 

information in order to install the appliance in a 

correct place.

Installation Location

•  Install the appliance on a flat floor of hard 

material that is strong enough to support a fully 

loaded appliance. (Allowable slope under the 

appliance: 1º)

•  Never try to level any uneven floor by putting 

pieces of wood, cardboard or similar materials 

under the appliance.

•  If it is impossible to avoid positioning the 

appliance next to a gas cooker or coal burning 

stove, an insulation (85 X 60 cm) covered with 

aluminium foil on the side facing the cooker or

stove must be inserted between the two 

appliances.

•  Ensure that when the appliance is installed, it is 

easily accessible for a service technician in the 

event of a breakdown.

•  Additional clearance for the wall should have 

10

cm

 for the rear and 

2 cm

 for right and left side.

WARNING

•  This appliance must only be used for domestic 

household purposes and should not be used in 

mobile applications.

NOTE

•  Do not install this appliance on a raised surface 

or platform, plinth or stand. It may cause injury 

or serious malfunctioning.

Ventilation

•  Make sure that air circulation around the 

appliance is not impeded by carpets, rugs, etc.

Ambient Temperature

•  Do not install the appliance in rooms where 

freezing temperatures may occur. Frozen hoses 

may burst under pressure. The reliability of the 

electronic control unit may be impaired at 

temperatures below freezing point.

•  If the appliance is delivered in winter and 

temperatures are below freezing, place the 

appliance at room temperature for a few hours 

before putting it into operation.

Electrical Connection

• Do not use an extension cord or double adapter.
• Always unplug the appliance and turn off the 

water supply after use.

• Connect the appliance to an earthed socket in 

accordance with current wiring regulations.

•  The appliance must be positioned so that the 

plug is easily accessible.

•  Power outlet must be within 1.5 meters of either 

side of the appliance.

WARNING

• Repairs to the appliance must only be carried out

by qualified personnel. Repairs carried out by 

inexperienced persons may cause injury or 

serious malfunctioning. Contact your local 

authorised LG repairer.

• The power plug must be plugged into an 

appropriate outlet socket that is installed and 

grounded/earthed in accordance with all local 

codes and ordinances.

10 cm

2 cm

2 cm

Summary of Contents for WT22VT6HK









































Reviews: