The use of non-LGB power sup-
plies will void your warranty.
Use this model with LGB power
supplies with an output at least 2
amps. For more information on
LGB power supplies for indoor,
outdoor and multi-train operation,
see the LGB catalog.
Attention! After extended opera-
tion, this model may leave carbon
dust or other debris around the
track. This dust and debris can
stain carpet and other materials.
Consider this when setting up
your layout. Ernst Paul Lehmann
Patentwerk and LGB of America
are not liable for any damages.
SERVICE
Do-It-Yourself Service Levels
Level 1 - Beginner
Level 2 - Intermediate
Level 3 - Advanced
Attention! Improper service will
void your warranty. For quality
service, contact your authorized
retailer or an LGB factory service
station (see Authorized Servi-
ce).
Lubrication 1
The side rod ends should be lubri-
cated occasionally with a small
amount of LGB Maintenance Oil
(50019).
Cleaning 1
This model can be cleaned exter-
nally using a mild detergent and
gentle stream of water. Do not
immerse this model.
Replacing the light bulbs 1
Lanterns (lower front): Pull the
lantern housing away from the
model. Remove and replace the
bulb.
Lanterns (upper front): Pull the
lantern forward to remove it from
the smokebox. Carefully pull on
the cable to remove the light bulb
from the lantern housing. Remove
and replace the bulb.
Lanterns (rear): Remove the
screw holding the lantern on the
body. Pull off the lantern. Remove
and replace the bulb.
Cab light: Using tweezers, remo-
ve and replace the bulb.
Replacing the smoke
generator 2
- Turn the smoke generator and
pull it from the model (Fig. 4).
- Cut the wires to the old genera-
tor and attach them to the repla-
cement generator (Fig. 5).
- Insulate the connections and
push the replacement generator
into the stack (Fig. 6).
Replacing the motor
If the motor needs to be replaced,
contact your retailer or an LGB
Service Station (see Authorized
Service).
Attention! If the motor is repla-
ced, generously lubricate the
gears with LGB Gear Lubricant
(51020).
Attention! Make sure that the
drive rods do not bind. Binding
can cause serious damage to the
model.
Replacing the brushes, pick-up
shoes or wheelsets
If the brushes, pick-up shoes or
wheelsets need to be replaced,
contact your retailer or an LGB
Service Station (see Authorized
Service).
Attention! If the wheelsets are
removed, generously lubricate
the gears with LGB Gear Lubri-
cant (51020).
Maintenance parts
50010 Smoke and Cleaning
Fluid
50019 Maintenance Oil
51020 Gear Lubricant
55020 MTS Decoder
62205 Motor
63120 Brushes, 14mm, 16mm,
8 pieces
63218 Standard Pick-Up
Shoes, 2 pieces
65853 Smoke Generator, 5V
68511 Plug-In Bulb, Clear, 5V,
10 pieces
AUTHORIZED SERVICE
Improper service will void your
warranty. For quality service,
contact your authorized retailer or
one of the following LGB factory
service stations:
Ernst Paul Lehmann Patentwerk
Reparatur-Abteilung
Saganer Strasse 1-5
D-90475 Nürnberg
GERMANY
Telephone: (0911) 83707 0
Fax: (0911) 8370770
LGB of America
6444 Nancy Ridge Drive
San Diego, CA 92121
USA
Telephone: (619) 535-9387
Fax: (619) 535-1091
You are responsible for any ship-
ping costs, insurance and
customs fees.
Hint: Information on LGB repair
9
