background image

Chapter 1: Pearl Docking Station

6) Connect one of the provided HEPA filter assemblies between the SmartFlow system and the

Induction Chamber.

7) Connect the opposite end of the HEPA filter assembly to the provided anesthesia gas supply tube

and then connect the other end of the anesthesia gas supply tube to one of the output manifold
connectors on the SmartFlow Anesthesia System, or equivalent (Figure 1-5).

Note:

For imaging beds not requiring a HEPA filter, connect the anesthesia gas supply tube dir-

ectly to the rotameter. For other vaporizers, it may be necessary to remove the connector that con-
nects to the SmartFlow System and replace it with an appropriate fitting.

CAUTION:

The Pearl

®

 Imaging System Docking Station is compatible only with anesthesia

systems that supply isoflurane gas. The flow rate and pressure into the instrument should not
exceed 1 liter per minute and 1 psi, respectively. If the pressure exceeds 5 psi, the rotameter
will not accurately show the flow to the nose cone.

ATTENTION:

La station d'amarrage de Pearl n'est compatible qu'avec les systèmes d'anesthésie qui
fournissent le gaz isoflurane. Le débit et la pression dans l'instrument ne devraient pas
excéder 1 litre par minute et 6.9 kPa, respectivement. Si la pression excède l'estimation de
34.5 kPa, le rotamètre ne montrera pas en juste proportion l'écoulement au cône de nez.

D

K

E

F

N

J

K

M

G

J

K

I

A

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

B

O

C

J

EQUIPMENT LEGEND

EX.

EX.

OXYGEN TANK

OXYGEN REGULATOR

SMARTFLOW ANESTHESIA SYSTEM

SMARTFLOW VAPORIZER

INDUCTION CHAMBER WITH HEATER

WATER PUMP

PEARL IMAGER

PEARL ROTAMETER

PEARL IMAGER IMAGING BED OR CLEAN BOX

CHARCOAL FILTER CANISTER

HEPA FILTER ASSENBLY (9957-055) 
FOR 9930-022 PEARL CLEAN BOX

DOCKING STATION ROTAMETER AND STAND

PEARL DOCKING STATION

10’ TUBING ASSEMBLY (#9957-056) INCLUDING
 WITH THE PEARL DOCKING STATION

TUBING ASSEMBLY INCLUDDED WITH 
THE PEARL IMAGER

OUT

OUT

OUT

IN

IN

IN

H

L

Figure 1-5. General representation of a typical system consisting of the docking station with the Pearl Imaging System
and SmartFlow Anesthesia System. Docking station rotameter (L) connects to optional HEPA filter assembly (K) and
anesthesia gas supply tube (N) before connecting to a port on the SmartFlow Anesthesia System (C).

Page 4

Summary of Contents for 5700-DS





















Reviews: