background image

 

4.  Share current port (only available for parallel model) 

5.  Parallel port (only available for parallel model) 

6.  Intelligent slot 

7.  Power stage fan 

8. 

External maintenance bypass switch port

 

9.  Input circuit breaker 

10. Input/Output terminal(Refer to Diagram 2 for the details) 

11. External battery connector 

12. Output terminal: connect to mission-critical loads 

13. Grounding terminal 

14. Utility input terminal 

15. Battery bank output circuit breaker 

 

2-3. Single UPS Installation

 

Installation and wiring must be performed in accordance with the local electric laws/regulations and execute the 
following instructions by professional personnel. 

1) 

Make sure the mains wire and breakers in the building are enough for the rated capacity of UPS to avoid 

the hazards of electric shock or fire. 

NOTE:

 Do not use the wall receptacle as the input power source for the UPS, as its rated current is less than 

the UPS’s maximum input current. Otherwise the receptacle may be burned and destroyed. 

2)  Switch off the mains switch in the building before installation. 

3)  Turn off all the connected devices before connecting to the UPS. 

4)  Prepare wires based on the following table: 

Model 

Wiring spec (AWG) 

Input 

Output 

Battery 

Ground 

6K 

10 

10 

 

10 

6KL 

10 

10 

10 

10 

10K 

 

10KL 

NOTE 1: 

The cable for 6K/6KL should be able to withstand over 40A current. It is recommended to use 

10AWG or thicker wire for safety and efficiency. 

NOTE 2: 

The cable for 10K/10KL should be able to withstand over 63A current. It is recommended to use 

8AWG or thicker wire for safety and efficiency. 

NOTE 3: 

The selections for color of wires should be followed by the local electrical laws and regulations. 

5) 

Remove  the  terminal  block  cover  on  the  rear  panel  of  UPS.  Then  connect  the  wires  according  to  the 

following terminal block diagrams: (Connect the earth wire first when making wire connection. Disconnect the 

earth wire last when making wire disconnection!) 

Summary of Contents for Adapt BX 10K




























Reviews: