background image

 

 

3. Operations 

3-1. Button Operation 

Button 

Function   

ON/Enter Button   

  Turn on the UPS: Press and hold the button more than 0.5s to turn on the UPS. 

  Enter Key: Press this button to confirm the selection in setting menu. 

OFF/ESC Button   

  Turn off the UPS: Press and hold the button more than 0.5s to turn off the UPS.   

  Esc key: Press this button to return to last menu in setting menu.   

Test/Up Button 

  Battery test: Press and hold the button more than 0.5s to test the battery while in 

AC mode, or CVCF mode. 

  UP key: Press this button to display next selection in setting menu. 

Mute/Down Button   

  Mute the alarm: Press and hold the button more than 0.5s to mute the buzzer. 

Please refer to section 3-4-9 for details.   

  Down key: Press this button to display previous selection in setting menu. 

Test/Up + 

Mute/Down Button 

  Press and hold the two buttons simultaneous more than 1s to enter/escape the 

setting menu.   

* CVCF mode means converter mode.   

3-2. LED Indicators and LCD Panel   

 

LED Indicators: 

There are 4 LEDs on front panel to show the UPS working status: 

Mode                    LED 

Bypass 

Line 

Battery 

Fault 

UPS Startup 

● 

● 

● 

● 

Bypass mode 

● 

○ 

○ 

○ 

AC mode 

○ 

● 

○ 

○ 

Battery mode 

○ 

○ 

● 

○ 

CVCF mode 

○ 

● 

○ 

○ 

Battery Test 

● 

● 

● 

○ 

ECO mode 

● 

● 

○ 

○ 

Fault 

○ 

○ 

○ 

● 

Note: 

 means LED is lighting, and 

 means LED is faded.   

LCD panel 

LED indicators 

Summary of Contents for Adapt BX 10K




























Reviews: