background image

 

6

Option Switch 3 & 4: Low Voltage Limit Select – Low voltage limit is the 
voltage level at which battery operation starts.  You may set the low voltage limit 
of the UPS to 180V, 190V, or 200V. The factory setting is 190V. This option 
reduces excessive battery usage in brownout conditions. Make sure your 
computer equipment can operate at 180 VAC before selecting the lowest limit 
(most will). Refer to the tables below to change switch settings:  

 

BATTERY TEST BUTTON 

 
The Battery Test Button (5) on the 400 and 600 VA models tests the condition of 
the battery.  If the charge is sufficient, the UPS lights the Battery Light (2), runs 
on battery power for 15 seconds, then returns to mains power. If the battery fails 
the test, the Check Light (3) illuminates and the UPS immediately returns to 
mains power.  The Check Light remains lit while on mains power. A battery in 
unacceptable condition requires recharge or replacement of the battery.  
 
Pressing the Battery Test Button (5) also silences alarms.  

 

BATTERY CARE AND USE 

 
STORAGE: If the unit is not in continued use, plug in the UPS every 4 to 6 
months for 12 hours to recharge the battery. Warranty is void if the battery 
discharges below the minimum battery cutoff point.  To prevent such discharge, 
DO NOT leave UPS ON for more than two days without plugging it in.  
 
BATTERY LIFE & REPLACEMENT: Excessive battery use, storage at high 
ambient temperatures, and lengthy periods in a discharged state greatly reduce 
battery life. Your UPS maximizes battery life by limiting the depth of battery 
discharge. You may replace the UPS battery yourself, but if you feel unqualified, 
refer battery replacement to qualified personnel.  Contact your local dealer or call 
Liebert for a replacement battery. 
  
WARNING: To replace batteries, turn OFF UPS and unplug it from mains supply.  
 
CAUTION: Observe proper precautions. When replacing batteries, use the same 
number and type of batteries. Proper battery disposal required. Refer to local 
codes for disposal requirements. Do not open or mutilate battery. Released 
electrolyte is harmful to skin and eyes and is toxic. 

250 VA MODEL 

VOLTAGE 

SWITCH #3 

SWITCH #4 

200V 

OFF 

N/A 

190V 

ON 

OFF 

180V 

ON 

ON 

 

400/600 VA MODELS 

VOLTAGE 

SWITCH #3 

SWITCH #4 

200V 

ON 

N/A 

190V 

OFF 

OFF 

180V 

OFF 

ON 

 

Summary of Contents for PowerSure PS250-50S, PS400-50S













Reviews: