background image

 

6

INTERFACE FUNCTION 

DB25 

ADAPTER 

UPS Shutdown/Active High* 

19 

On Battery/Return 

17 

On Battery/Normally Open 

16 

Low Battery/Normally Open 

11 

Low Battery/Return 

UPS Shutdown/Return 

*Remote Shutdown (5-12V DC, 5-10 mA. max.); battery 
operation 

 
 
 

COMPUTER/LAN INTERFACE 

(400/600 VA ONLY) 

 
Optional SiteNet® 1 kits provide connection to a wide range of popular computer 
operating systems such as Novell, UNIX, UNISYS, SUN, WINDOWS and many 
others.  SiteNet® 1 software automatically performs an orderly shutdown of 
computer operating systems in the event of a power outage and/or low battery 
conditions.  

 

The SiteNet ®1 kit supplies a cable to connect supported computer systems to 
the UPS communications port (10).  The table below shows connector details.  
 

Note: Your dealer supplies computer communications kits separately, if you wish. They 
come with installation instructions, cable connections, and appropriate computer software.  
 

(-)

(+)

330 Ohms

Open Collector

Return

COLLECTOR TO EMITTER

Maximum voltage and current on pins

11 & 16 are +40V DC; 1.0mA

1

1

Summary of Contents for PowerSure PS250-60S














Reviews: