2
21
7
2
8
1
I
17
4
G
F
1
3
H
IMPORTANT!
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS NEEDED
TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
IMPORTANT!
NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS
NÉCESSAIRES POUR L'INSTALLATION.
1.
Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top
of the LEFT PIVOT ARM (A).
If equipped with Lifepulse, connect the 2-PIN HEART RATE CONNECTOR
(B) leading from the HANDLEBAR to the 2-PIN CONNECTOR (C) extending
from the top of the LEFT PIVOT ARM. Carefully slide the excess HEART
RATE CABLE into the top of the LEFT PIVOT ARM.
Align the mounting holes of the LEFT HANDLEBAR with the mounting holes
at the top of the LEFT PIVOT ARM. Secure them together using three
SCREWS (1).
NOTE:
BE CAREFUL NOT TO PINCH THE HEART RATE CABLE WHEN
SECURING THE LEFT HANDLEBAR TO THE LEFT PIVOT ARM.
2.
Locate one LEFT FRONT ROCKER COVER (5) and the LEFT BACK
ROCKER COVER (6). Position the LEFT BACK ROCKER COVER over the
user side of the ROCKER ARM making sure that it seats fully over the
BULLHORN MOUNTING BRACKET (D). Place the FRONT ROCKER
COVER over the opposite side of the ROCKER ARM in the same manner.
Secure the COVERS using two PHILLIPS PAN HEAD SCREWS (2).
Tighten the SCREWS securely. Do not over-tighten the SCREWS.
3.
Locate one FRONT PIVOT ARM COVER (9) and one BACK PIVOT ARM
COVER (10). Position the BACK PIVOT ARM COVER over the user side of
the ROCKER ARM making sure that it interlocks with the ROCKER COVER.
Place the FRONT PIVOT ARM COVER over the opposite side of the PIVOT
ARM in the same manner. Secure the COVERS using two PHILLIPS PAN
HEAD SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the
SCREWS.
4.
Locate the LEFT BULLHORN (13). Secure the BULLHORN to the
BULLHORN MOUNTING BRACKET (D) using two FLAT HEAD SCREWS
(1). Tighten the SCREWS securely. Locate and attach the LEFT
BULLHORN COVER (15) to the base of the BULLHORN using one SCREW
(22). Tighten the SCREW securely. Do not over-tighten the SCREW. Slide
the GASKET (E) downward to meet the BULLHORN COVER.
5.
Repeat steps one through four to install the RIGHT ROCKER COVERS (5 &
6), PIVOT ARM COVERS (9 & 10), BULLHORN (14) and BULLHORN
COVER (16).
NOTE:
THE RIGHT PIVOT ARM COVERS ARE REVERSED FRONT
AND BACK. THE SCREWS WILL BE INSTALLED FROM THE REAR.
6.
Unwrap the MAIN WIRE and HEART RATE HARNESS (F & G) leading from
the MONOCOLUMN (H). Feed the WIRE HARNESSES through the
CONSOLE SUPPORT ASSEMBLY TUBE (I) located at the top and front of
the MONOCOLUMN. Locate the CONSOLE SUPPORT ASSEMBLY (7) and
position it near the top of the MONOCOLUMN. Feed the WIRE
HARNESSES through the CONSOLE SUPPORT ASSEMBLY as shown.
Align the bottom mounting holes of the CONSOLE SUPPORT ASSEMBLY
with those in the CONSOLE SUPPORT ASSEMBLY TUBE. Secure them
together using six SCREWS (1). Tighten the SCREWS securely.
NOTE:
BE CAREFUL NOT TO DAMAGE THE WIRE HARNESSES (E &
F) WHEN ROUTING IT THROUGH THE CONSOLE SUPPORT
ASSEMBLY OR WHEN MOUNTING THE CONSOLE SUPPORT
ASSEMBLY TO THE CONSOLE SUPPORT ASSEMBLY TUBE.
7.
Locate the ACCESSORY TRAY (17). Slide the ACCESSORY TRAY into the
top of the MONOCOLUMN (H) as shown. Be sure the ACCESSORY TRAY
is fully seated.
NOTE:
BE CAREFUL NOT TO DAMAGE THE MAIN WIRE HARNESS
WHEN SLIDING THE ACCESSORY TRAY INTO THE MONOCOLUMN.
Secure the accessory tray to the CONSOLE SUPPORT ASSEMBLY using
two SCREWS (3). Tighten the SCREWS securely. Do not over-tighten the
SCREWS.
9
11
1
10
2
B
C
A
5
6
2
13
1
15
22
A
D
E
Summary of Contents for 90X
Page 1: ...95Xi 93X 90X Total Body Trainers Assembly Instructions...
Page 7: ......
