background image

STEP 19:

19

FIGURE 19

•   

 

Insert the two GUIDE RODS (19) into the BASE (25) as shown in FIGURE 19. Lubricate the GUIDE RODS  (19) with a slicon or teflon

spray that is available at most hardware stores.

•    Slide two WEIGHT STACK CUSHIONS (47) down over the GUIDE RODS (19). See FIGURE 19.

•  

  

Using 

EXTREME CARE 

slide twenty WEIGHT PLATES (106) down over the GUIDE RODS (19) with the the key-hole facing as

shown in FIGURE 19.

•   

 SECURELY 

assemble the WEIGHT STACK SHAFT (50) to the HEAD PLATE (53) using one 3/8 X 1-1/4” BOLT (88) and one 3/8”

BLACK LOCK  WASHER (81). 

(Note:

 

The bolt hole in the HEAD PLATE (53) should be on top.)

•   

 

Carefully Slide the HEAD PLATE ASSEMBLY down over the GUIDE RODS (19) onto the weight stack as shown.

•    Slide two 13/16” SHAFT COLLARS (78) over the GUIDE RODS (19) as shown in FIGURE 19.

•   REPEAT the above steps to  assemble the weight stacks on the PRESS WEIGHT STACK BASE (24) and the LEG WEIGHT STACK

BASE (23). 

(NOTE:  Use four WEIGHT STACK CUSHIONS (47) (two per guide rod!) on the LEG WEIGHT STACK BASE (23)

as shown in FIGURE 19.)

TWO

PER

SIDE!

108

107

106

50

3/8” LOCK
WASHER  81

53

19

78

3/8 X 1-1/4” 88

24

23

25

47

•    Apply one set of WEIGHT STACK LABELS - LBS. OR NUMBERED 1-20 (107) (108) to each WEIGHT PLATE (106). See FIGURE 19.

TWO PER SIDE

ON THIS STACK ONLY!

Summary of Contents for Exercise Bike Lifecycle 8500




































Reviews: