Life Gear 75112 Owner'S Manual Download

Page: 8 / 26

HARDWARE PACKING LIST

Part # Description Quantity

Hex Head Bolt M6x47 -----------------------------------------------------------------------------------------2

Washer Ø 20xØ 8.5x1.5 ---------------------------------------------------------------------------------------12

Lock Nut M8 ------------------------------------------------------------------------------------------------------- 6

Lock Nut M6 ------------------------------------------------------------------------------------------------------- 2

Washer Ø 16xØ 6.5x1.0 ----------------------------------------------------------------------------------------4

Hex Head Bolt M8x23 -----------------------------------------------------------------------------------------2

Hex Head Bolt M8x50 -----------------------------------------------------------------------------------------2

Square End Cap -------------------------------------------------------------------------------------------------- 1

Hex Head Bolt M8x38 -----------------------------------------------------------------------------------------2

Bolt M6x20 --------------------------------------------------------------------------------------------------------- 8

Washer Ø 13xØ 6.5x1.0 ----------------------------------------------------------------------------------------8

Nut Cap Ø 27xØ 13.5 ------------------------------------------------------------------------------------------- 2

Pivot Arm Ring --------------------------------------------------------------------------------------------------- 2

NOTE:

The parts described above are all the parts you need to assemble this inversion table.

Before you start to assemble, please check the hardware packing to make sure they are
included.

All the other parts described in page 6 parts list are pre-assembled in the factory.

ASSEMBLY

Set all parts in a clear area on the floor and remove the packing materials. Refer to the part lists for help
to identify the parts. Follow the steps to assemble the inversion table.

Double Open Wrench

2 PCS

Phillips Screwdriver

1 PC

Summary of Contents for 75112



























Search results

Summary of Contents for 75112

Reviews:

Related manuals for 75112

Brands by name

Popular brands

Life Gear 75112, Owner'S Manual

Search results

Summary of Contents for 75112

Reviews:

Related manuals for 75112

Brands by name

Popular brands