background image

22

Service  your  HRV  on  a  regular  schedule  for 

optimum operating efficiencies and a prolonged life of 

the equipment.

Motor

Access  the  motor  through  the  front  service  doors. 

Note  the  heat  exchanger  core  can  be  removed  to 

provide more room. See 

HRV 

C

ore

 

in this section.

HRV

 

Core

Access  the  heat  exchange  core  through  the  front 

service  door.  Provide  special  care  and  attention  to 

this  component:  the  edges  may  be  sharp  and  the 

core,  itself, susceptible to damage if dropped.
When  removing  the  core,  note  the  location  from 

which  it  is  removed.  Remove  the  core  by  carefully 

pulling  it  outward from  the  unit  and  sliding  it  evenly 

along  its  guide  rail  supports  (found  on  the  top  and 

bottom corners and on either

side  of  the  core).  Note  the  core  may  have  some 

resistance  when  sliding  out.  Avoid  tilting  the  core  as 

this will result in its edges catching the guide rails and 

temporarily preventing its removal.
In  most  cases,  all  the  core  requires  is  a  wash  in  a 

mild detergent and warm water to completely clean it. 

Do not use harsh  chemicals,  as  their  use  may  cause 

corrosion  in  the HRV. The time required between each 

core  service  depends  on  the  application  in  which  the 

HRV is installed.
Service  may  be  required  as  often  as  one  month,  two 

months  or  at  the  very  least,  cleaned  every  six 

months. 

When  reinstalling  the  core,  note  the 

foam  location  and  drip  edge  location  for 

proper  core  placement 

(see  diagram below).

With the core in its proper position, place the bottom 

corner into  its  guide  rail  support,  then  place  the  left 

side,  the  right  side,  and  finally  the  top  corner,  into 

place  in  the  same fashion. Once the core is in place, 

push  the  core  evenly  into the cabinet until it reaches 

the back.
Note  the  core  will  protrude  slightly  from  the  front  of 

the cabinet,  this  is  so  the  access  door,  when  closed, 

ensures  a tight fit.

DRAIN PANS

FILTER

FILTER

CORE

Note

 

location

 

and

 

arrangement

 

of

 

cores

 

and

 

filters

 

when

 

removing.

Maintenance

 

and

 

Service

Summary of Contents for 1200 POOL

































Reviews: