background image

3. Service and Technical Data

Preventive Maintenance Schedule

Item

Weekly

Monthly

Biannually

Console Overlays

Clean

Inspect

Bottle Holders / Accessory
Trays

Clean

Inspect

Console Mounting Bolts

Inspect

Hardware

Inspect

Frame / Seat Post

Clean

Inspect

Plastic Covers

Clean

Inspect

Lifepulse Sensors

Clean / Inspect

Leg Levelers

Inspect / Adjust

Pedals / Straps

Clean

Inspect

Preventive Maintenance Tips

NOTE: Safety of the equipment can be maintained only if the equipment is examined regularly for damage or wear.
Keep the equipment out of use until defective parts are repaired or replaced. Pay special attention to parts that are
subject to wear, as outlined below.

REMARQUE : Pour assurer la sécurité du matériel, il convient de l’inspecter régulièrement afin de déceler tout signe
d’usure ou d’endommagement. N’utilisez pas l’appareil avant d’avoir réparé ou remplacé les pièces défectueuses.
Portez une attention toute particulière aux pièces qui s’usent, comme indiqué ci-dessous.

The following preventive maintenance tips will keep the product operating at peak performance:

• Locate the product in a cool, dry place.
• Clean the display console and all exterior surfaces with an approved or compatible cleaner (see Approved and

Compatible Cleaners) and a microfiber cloth.

• Long fingernails may damage or scratch the surface of the console; use the pad of the finger to press the selection

buttons on the console.

• Clean the top surface of the pedals regularly.

NOTE: When cleaning the exterior of the unit, a non-abrasive cleaner and soft cotton cloth are strongly
recommended. At no time should cleaner be applied directly to any part of the equipment.

Approved and Compatible Cleaners

Two preferred cleaners have been approved by reliability experts: PureGreen 24 and Gym Wipes. Both cleaners will
safely and effectively remove dirt, grime and sweat from equipment. PureGreen 24 and the Antibacterial Force
formula of Gym Wipes are both disinfectants that are effective against MRSA and H1N1.

PureGreen 24 is available in a spray which is convenient for gym staff to use. Apply the spray to a microfiber cloth and
wipe down the equipment. Use PureGreen 24 on the equipment for at least 2 minutes for general disinfection
purposes and at least 10 minutes for fungus and viral control.

Gym Wipes are large, durable pre-moistened wipes to use on the equipment before and after workouts. Use Gym
Wipes on the equipment for at least 2 minutes for general disinfection purposes.

Contact Customer Support Services to order these cleaners (1-800-351-3737 or email:

customersupport@lifefitness.com

).

Mild soap and water or a mild non-abrasive household cleaner can also be used to clean the display and all exterior
surfaces. Use a soft microfiber cloth only. Apply the cleaner to the microfiber cloth before cleaning. DO NOT use
ammonia or acid based cleaners. DO NOT use abrasive cleaners. DO NOT use paper towels. DO NOT apply cleaners
directly to the equipment surfaces.

Page 12 of 39

Summary of Contents for INRD-SLXX











































Reviews: