background image

 

2

For your information, please note following electronical specification of 

Treadmill: 

a. The input voltage: 240V±10% 

50-60HZ

 

b. Input current: 

6A 

c. Time Range: 0:00-99:99 

d. Speed Range: 0.8-16.00KM/H 

e. Distance Range: 0.00-99.9KM 

f. Calories range: 0-999CAL 

g. Pulse range: 50-200times/ minute 

IMPORTANT OPERATION INSTRUCTIONS 

z

  Be sure to read the entire manual before operating your machine. 

z

  Understand that changes in speed and incline do not occur immediately. Set your desired speed on the 

computer console and release the adjustment key. The computer will obey the command gradually.   

z

  Use caution while participating in other activities while walking on your treadmill; such as watching 

television, reading, etc. These distractions may cause you lose balance or stray from walking in the centre 

of the belt; which may result in serious injury. 

z

  In order to prevent losing balance and unexpected injury, NEVER mount or dismount the treadmill while the 

belt is moving. This unit starts at a very low speed. Simply standing on the belt during slow acceleration is 

proper before you have learned to operate this machine. 

z

  Always hold on to handrail while making control changes. 

z

  A safety key is provided with this machine. Remove the safety key will stop the walking belt immediately; 

the treadmill will shut off automatically. Insert the safety key will reset the display.   

z

  Do not use excessive pressure on console control keys. They are precision set to function properly with 

little finger pressure.   

FOLDING INSTRUCTIONS 

When folding the treadmill, pull out the handles on the holding spanner and place the main frame at 

corresponding position. By then, the handle bolt will appear automatically. After that, move the treadmill to 

another place so as to make it occupy a smaller area. Before usage, place the treadmill to the position you would 

like to do exercise, and lift its main frame by right hand and pull out the handles and place them on the floor 

slowly. Then the handles will appear automatically. Finally screw down the handles firmly to release yourself from 

being worried about the safety during exercise.     

Summary of Contents for BOOMER XT
















Reviews: