background image

Single End Connection Application Accessories Kit

01 (or 02)

 

Front Connector

Silicon Gasket

U Steel Plate

Anti-skidding Clip

1 pc

1 pc

1 pc

1 pc

Front Connector Accessories Kit

End Cap Accessories Kit

The Tail Plug

U Steel Plate

Anti-skidding Clip

Silicon Gasket

1pc

1pc

1pc

1pc

Fig

.

1

 

Minimum

 

bent

 

diameter

 

90mm

Light Surface

Φ

90mm

Light

Moods

TM

MINI Flat LED Neon Ribbon Light

USER MANUAL

MNFLSC-24V-72

(Green/Blue/Warm White/White/Cool White/Daylight White)

1. Model: MNFLSC-24V-72
2. Rated input voltage: DC 24V
3. Rated Power: 5W/m
4. Dimension: 9*18mm
5. LED quantity: 72LEDs/mtr
6. LED Spacing: 13.88mm
7. Min. cutting length: 83.3mm( 6LEDs) 
8. Max. running length: 15 mtrs for single end feed or 30mtrs
for double ends feed. 
9. Light color: Single Color
(Green/Blue/Warm White/White/Cool White/Daylight White) 
10. Min. bent diameter: 90mm; Do not twist the light .
11.Protection rate: IP68
12.Protection rate for IP68: Protected against dust and submersion 
in water (1meter above).
NOTE: All connector joints must be connected correctly to achieve 
IP68 rating
13.Can be cut and extended
14.Long lifetime: 5 years
15.Working ambient temperature: -4°~113°F (-20°~45°C)
16.Operating (bending) ambient temperature: 32°~113°F  (0°~45°C)

Palm Coast, Florida, USA / Los Angeles, California, USA /  Pribram, Czech Republic / Birmingham, U.K. / Kuala Lumpur, Malaysia / Mumbai, India
Email: christian@aveoengineering.com / Web: www.aveoengineering.com

DO-160G

tested

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION AND LEAVE A COPY FOR THE END 

USER/MAINTENANCE ENGINEER FOR FUTURE REFERENCE

FEATURES

WARNING AND CAUTION

ACCESSORIES (SOLD SEPARATELY)

ASSEMBLY AND INSTALLATION

FIGURES

WARNING

1. Before making any cuts,installation,maintenance or connection, be sure

    the mains is disconnected!

2. NOTE: ALL CONNECTOR JOINTS MUST BE CONNECTED CORRECTLY TO

    ACHIEVE IP68 RATING.

3. Please operate this flex light  according to the instructions, and confirm 

    the work voltage, it must be matched with product requirements.

4. Please confirm the polarity of connector before insertion front connection cable.

5. Connect and cut this product correctly. Any wrong operation will damage this

    product.

6. No pressing on this product during storage, long term pressing may lead to damage.

7. Using qualified DC power supply.

8. Min. bent diameter 90mm, see Fig.1.

9. Do not twist the light as Fig.2 and follow the correct bending direction as Fig.3.

10. Do not hang this light in the air as Fig.4.

11. Cutting at the wrong location will result in a failure of the light! See Fig.5.

CAUTION

1. Suitable for mounting on normally flammable surfaces..

2. Use only factory-recommended connectors and accessories.

3. To ensure its long life span, operate the light properly in accordance with the

     instructions.

4. Do not operate in more than 113°F (45°C) ambient temperature.

5. Assemble the DIY Connector correctly as in Fig.6.

6. Max. running length depends on the energizing way as Fig.7 shown.

7. Warm White,Cool White and Daylight color reference ANSI STANDARD.

8. Do not operate light when ambient temperature is below 32°F (0°C) thais may injure  

    the light .

1. Turn off the electricity before operation.

2. Cut the light at correct location (if need).

3. Assemble the light according to Fig.8.

4. Install U channel and light according to Fig.9 (Only applicable to DIY accessories) .

5. Wire all connectors to the power line and check wiring of the whole circuit.

   Cable color coding basics Refer to Fig.10.

Summary of Contents for MNFLSC-24V-72

Page 1: ...ELY ASSEMBLY AND INSTALLATION FIGURES WARNING 1 Before making any cuts installation maintenance or connection be sure the mains is disconnected 2 NOTE ALL CONNECTOR JOINTS MUST BE CONNECTED CORRECTLY TO ACHIEVE IP68 RATING 3 Please operate this flex light according to the instructions and confirm the work voltage it must be matched with product requirements 4 Please confirm the polarity of connect...

Page 2: ...ctor Pins For 01 Type Front Connector MINI Flat LED Neon Ribbon Light USER MANUAL MNFLSC 24V 72 Green Blue Warm White White Cool White Daylight White Palm Coast Florida USA Los Angeles California USA Pribram Czech Republic Birmingham U K Kuala Lumpur Malaysia Mumbai India Email christian aveoengineering com Web www aveoengineering com DO 160G tested 2 Twisting the light is forbidden and observe to...

Page 3: ... for Max length 15m Double ends connection for Max length 30m Fig 8 DIY Connector Assemble Diagram For 02 Type Front Connector Connector Pins Connector Pins Front Connector U Steel Plate U Steel Plate Anti skidding Clip Rubber G asket The Tail Plug Light Anti skidding Clip Rubber Gasket Front Connector Assemble Front Connector Rubber Gasket U Steel Plate Anti skidding Clip Light Step 1 2 3 4 5 6 7...

Page 4: ...y we reserve the right to charge for time and parts Advances technology for the will be selected firstly 2 Warranty excludes below Any man made damages caused from improper operation assembly wiring connection installation transport and storage Improper input voltage current operating and working environment The product appears to have excessive physical damage Damage due to natural disasters and ...

Reviews: