background image

     

 

 

 

Suzhou Lily Tech. Co., Ltd. 

 

suzhoulilytech@hotmail.com        www.suzhoulily.com.cn        Page 1, Total pages 6 

 

               

 

Z

Z

L

L

-

-

3

3

3

3

0

0

A

A

 

 

E

E

l

l

e

e

c

c

t

t

r

r

o

o

n

n

i

i

c

c

 

 

T

T

h

h

e

e

r

r

m

m

o

o

s

s

t

t

a

a

t

t

 

 

 

 

I

I

n

n

s

s

t

t

r

r

u

u

c

c

t

t

i

i

o

o

n

n

 

 

M

M

a

a

n

n

u

u

a

a

l

l

 

 

1. Features   

ZL-330A is an electronic thermostat for cooling. The device is ideally fitted to refrigeration equipment for cold 

storage. 

 

2. Main Function

 

  Temperature measurement                                           

  Temperature display 

  Temperature calibration                                                 

  Compressor delay protection   

  Blustering when system warning     

  Sensor problem warning     

  External warning input 

  Defrost control:

 Timed defrost , manual defrost and defrost water d

ripping

 

  Fan control

 

  The conditions of the end of defrost: is time and temperature 

 

3. Main Specification   

  Temperature Sensor:            NTC                                     

  Setting Range:                      -40

120

 

  Display Range:                      -50

130

                         

  Working Temperature:          -10

45

 

  Storage Temperature:          -30

70

                           

  Humidity:                                  5

85%RH (without dewing) 

  Power Supply:                        185 ~ 245VAC 50/60HZ   

  Terminal Wire:                        <= 2 * 1.5mm

2

 or 1 * 2.5mm

2

 

  Load Current:                          3A 250Vac

Resistive load

 

  Case:                                        PC + ABS Fire Proof 

  Protection Degree:                IP30 

 

4. Operation Instruction 

4.1 Display Indication 

Panel LED Indication 

LED 

On 

Off 

Blinking 

Summary of Contents for ZL-330A






Reviews: