Suzhou Lily Tech. Co., Ltd.
Page 3. Total 5 pages
Code parameter table:
Code
Function
Range
Remark
Factory
Default
t0
Temp. control mode
H/C
H: heat; C: cool
H
t1
Temp. hysteresis
0.1
～
20
℃
0.1
t2
Time delay protection for Temp. load
0
～
30 min
0
t3
Temp. calibration
-9.9
～
+9.9
℃
0
t4
Temp. high limit (relative value, R1)
0
～
20
If 0, no high temp. limit
0.2
t5
Temp. low limit (relative value, R1)
0
～
20
If 0, no low temp. limit
0.1
t6
Temp. high warning point (relative value)
0
～
65
If 0, no high temp. warn
0
t7
Temp. low warning point (relative value)
0
～
65
If 0, no low temp. warn
0
h0
Humidity control mode
H/P
H: humidify; P: dehumidify
H
h1
Humidity hysteresis
1
～
20 %
2
h2
Time delay protection for Humi. Output
0
～
30 min
0
h3
Humidity calibration
-20
～
+20%
0
h4
Humidity high limit (relative value, R1)
0
～
20 %
If 0, no high humidity limit
5
h5
Humidity low limit (relative value, R1)
0
～
20 %
If 0, no low humidity limit
2
h6
Humidity high warning point (relative value)
0
～
80 %
If 0, no high humidity warn
0
h7
Humidity low warning point (relative value)
0
～
80 %
If 0, no low humidity warn
0
u0
Egg turn (R4, R5) deenergized time
0
～
999 min
If 0, no turn function
60
u1
Egg turn (R4, R5) energized time
0
～
999 sec
If 0, no turn function
30
u2
Egg turn times
0
～
999
If 0, turn without shop
0
u3
Exhaustion fan (R1) deenergized time
0
～
999 min
If 0, no exhaustion
120
u4
Exhaustion fan (R1) energized time
0
～
999 sec
If 0, no exhaustion
30
u9
Sensor selection
0/1
0: ZL-SHr03A
1: ZL-SHr05B
0
Control Function Instruction
Temperature control
Heat mode
【
t0 = H
】
When
Room temp.
≤
Set temp.
(
TP
) –
【
t1
】
, and
Temp. Output
(R3) has stopped for
【
t2
】
,
Temp. Output
(R3) will be energized.
When
Room temp.
≥
Set temp.
(
TP
),
Temp. Output
(R3) will be deenergized.
Cool mode
【
t0 = C
】
When
Room temp.
≥
Set temp.
(
TP
) +
【
t1
】
, and
Temp. Output
(R3) has stopped for
【
t2
】
,
Temp. Output
(R3) will be energized.
When
Room temp.
≤
Set temp.
(
TP
),
Temp. Output
(R3) will be deenergized.
Over high temperature limit protection (only for heat mode)
When
Room temp.
≥
Set temp.
(
TP
) +
【
t4
】
,
Fan Output
(R1) will be energized.
When
Room temp.
≤
Set temp.
(
TP
) +
【
t4
】
-
【
t5
】
,
Fan Output
(R1) will be deenergized.
