background image

IS792  ECN 4879 

Page 12 of 37 

 

 

year 

 

INSTALLATION AND COMMISSIONING 

3.1  TRANSPORTATION AND HANDLING 

The equipment must be transported and handled exclusively in upright position, 

in observance of the instructions printed on the packing. 

This  precaution  is  necessary  to  avoid  contamination  of  the  refrigerant  circuit  with 

compressor  lube  oil  with  resulting  valve  and  heat  exchanger  coil  failure  and  problems 
starting the electric motor or the risk of a gas leak. The manufacturer is not responsible for 
any problems due to transport executed in conditions other than those specified herewith.

 

The equipment is secured to a wooden pallet base, wrapped in a plastic film and packaged 

into a three waves  carton box.. 

The equipment must be handled using a fork lift truck or a pallet truck with suitable forks 

(fork length at least equal to 2/3 length of unit). 

 

3.2  POSITIONING 

Incorrect  positioning  can  cause  damage  to  the  equipment  and  generate  hazardous 

conditions  for  personnel.  The  installer  must  therefore  observe  the  following  general 
regulations:

 

  Make  sure  you  main

tain  a  minimum  of  11,8”  (30cm).  clearance  from  the  walls  and 

19,7” (50 cm) from the sides where the air inlets and outlets are located.. The room 
must be well ventilated. 

  Keep well away from sources of heat. Avoid direct sunlight 

  Remove packing material. 

 

  Remove accessories from inside the unit.

 

  Cartoon box or Wood base removal: using a hammer, tilt the cabinet to one side and 

loosen the two thread-forming screws, drag the cabinet from the back side holding the 
base still until the four castors have gone out from the containing holes, slightly tilt the 
cabinet backward and take the base away pulling it from the front side. 

  Use  gloves  when  handling  the 3 Waves  cartoon  box  or  the wooden base  to protect 

the hands from splinters.

 

  Position the equipment with the help of a level. Remove the protective PVC film from 

the external surfaces of the unit. 

Wait 24 hours after positioning the machine before starting it up, thus allowing the oil to 
return to the compressor and preventing it from breaking. 

 

3.3  WIRING AND ELECTRICAL HOOK-UP 

Receptacle installation and electrical wiring operations must be performed by a 

qualified electrician. For safety reasons adhere to the following indications: 

  Check that the electrical plant is suitably sized for the absorbed power of the unit. 

  If  the  electrical  socket  and  the  plug  on  the  equipment  power  cord  are 

incompatible, call technical service or your local distributor. 

Summary of Contents for BGBF-10






































Reviews: