background image

IS792  ECN 4879 

Page 15 of 37 

 

 

•"stand-by"  (the  device  is  switched  on  and  no  operating  cycle  is  running,  but  it  is 
possible to select one) 
•"off"  (the  device  is  switched  off  and  no  operating  cycle  is  running,  and  it  is  not 
possible to select any).  

If power is interrupted while in the "on" mode, when power is restored the device will be in 
the same state and the operational cycle will be restarted from the point reached when the 
power interruption occurred. 

If power is interrupted while in "stand-by" or "off" mode, when power is restored the device 
will be in the same state. 

 

4.2  SWITCHING THE DEVICE ON/OFF ("off"/"stand-by") 

Ensure no procedures are running 

•press 

B1

 for 5 s 

The  displays  will  blink  for  few  seconds  than  the  upper  display  will  show  the  actual  air 
temperature inside the cavity. 
In order to switch off the controller, press and hold the 

B1

key for 5 secs, the upper display 

will show the 

OFF

label. 

 

4.3  STARTING/STOPPING AN OPERATIONAL CYCLE ("on"/ "stand-
by") 

In order to stop an ongoing cycle 

•press 

B1

 and release 

the controller will switch into the stand-by mode. 
The regulators are switched off while in "stand-by" mode. 

 

4.4  THE DISPLAY  

In the "on" state, during normal operation, display 

DY1

 shows: 

•the  temperature  measured  by  the  needle  probe  if  a  set-temperature  chilling  or 
freezing cycle is ongoing 

•the temperature of the cabinet if a set-temperature chilling, or timed freezing or a 
storage cycle is ongoing. 

Display 

DY2

 shows: 

•the elapsed time for a blast chill or freezing cycle, if these are ongoing 

While  in  "stand-by"  mode,  display 

DY1

  shows  the  cabinet  temperature  and  display 

DY2

 

shows "- - -". 
While in "off" mode, display 

DY1

 shows "OFF" and display 

DY2

 is off. 

 

4.5  DISPLAYING THE TEMPERATURES DETECTED BY THE PROBES 

Summary of Contents for BGBF-10






































Reviews: