background image

IS212 ECN3592 

FOREWORD 

 
Thank  you  for  buying  this  Lincat  product,  which  we  hope,  will  give  you  years  of  trouble  free  service.  To 
ensure  you  receive  the  maximum  benefit  from  your  new  Griddle  please  take  the  time  to  read  these 
instructions carefully, following any directions given. 
 
We manufacture over 300 different items of catering equipment and are constantly adding to and improving 
the range. 
If you are thinking of extending your kitchen or renewing a catering appliance in the near future, see our sales 
brochures available from your local distributor or send for one direct from us before you make your decision.

 

 

IMPORTANT

 

Please read this page carefully before using the equipment.

 

 

WARNING

   

It is mandatory that all appliances are installed, commissioned and serviced by a qualified and 
competent person as defined by the regulations in force in the country of installation. 
Failure to comply will invalidate the warranty.

 

 

 

 

 

 

 

Whilst in operation, parts of the catering equipment will become hot.  Suitable precautions must be taken to 
avoid accidental burns; therefore, the appliance should be positioned to minimise the possibility of accidental 
touching.   
 

This appliance is for professional use and should be operated by suitably trained personnel.

 

 

 

CONSEQUENTIAL LOSS

 

 

Lincat Ltd. does not accept any responsibility for loss of food, production time, profit, etc., which may result 
from a breakdown of the equipment 

 
 

MAINTENANCE

 

 

These units must 

not

 be cleaned using a water jet. 

 
Clean units with warm water and detergent - do not use abrasives on outer surfaces of the appliance. 
Using a wire brush to cleanse the griddle plate of carbon deposits is acceptable however eye protection must 
be worn if using a wire brush.  

Summary of Contents for Silverlink 600 GS4













Reviews: