background image

17 

 
 
 

SERVICE

 

 

Gas catering equipment should be routinely serviced to ensure a long trouble free life.  With this in 

mind it is recommended that the appliances are serviced every 6 months by a competent gas engineer. 

 

For help regarding the installation, maintenance and use of your LINCAT equipment, please call:- 

 
 

LINCAT SERVICE HELP DESK 

 

 

01522 500881 

 

 

AUTHORISED SERVICE AGENTS 

 

We recommend that all servicing other than routine cleaning be carried out by our authorised service agents 
and will accept no responsibility for work carried out by other persons.  Note that for safe and efficient 
operation, appliances need regular servicing. 
 
Please quote both the model and serial numbers from the data plate attached to the unit.  Give brief details of 
the service requirement. 
 
If you know the part number of the part in question, please quote this information also. 
 
Lincat reserve the right to carry out any work under warranty during normal working hours, i.e. Monday to 
Friday, 8.30 a.m. - 5.00 p.m. 

 

CONDITIONS OF GUARANTEE 
 

The guarantee does not cover:- 
 
1) 

Accidental breakage or damage 

2) 

Operational misuse, wear and tear from normal usage, incorrect adjustment, or neglect. 

3) 

Incorrect installation, maintenance, modification or unauthorised service work. 

 
 
 
 
 
 
 

Utensils Direct - 01903 823888

www.utensilsdirect.co.uk

Summary of Contents for Silverlink 600 J10


















Reviews: