background image

IS 358  ECN 3592 

 

FOREWORD 

 
Thank you for buying this Lincat product, which we hope will give you years of trouble free service.  
To ensure you receive the maximum benefit from your new fryer please take the time to read this 
instruction book carefully, following any directions given. 
 
We  manufacture  over  300  different  items  of  catering  equipment  and  are  constantly  adding  to  and 
improving the range. 

If you‟re thinking of extending your kitchen or renewing a catering appliance in the near future, see 

our sales brochures available from your local distributor or send for one direct from us before you 
make your decision. 

 

 
IMPORTANT 

 

Please read this page carefully before initially using the equipment. 

 

 
WARNING  
 

This appliance must be installed and serviced by a registered engineer. 

 

 

 

 

 

 

Whilst in operation,  parts of the catering equipment will become hot.  Suitable precautions must be taken to 
avoid accidental burns, therefore the appliance should be positioned to minimise the possibility of accidental 
touching.   
 
This appliance is for professional use and shall be operated by qualified personnel. 

 
 
 

CONSEQUENTIAL LOSS 

 

Lincat do not accept any responsibility for loss of food, production time, profit, etc., which may result from 
a break-down of the equipment 
 

 
 

MAINTENANCE 

 

1)  

These units must 

not

 be cleaned using a water jet. 

2) 

Clean units with water and detergent - do not use abrasives.

  

 

 

 
 

 
 
 
 
 

 

Summary of Contents for Silverlink 600 J10


















Reviews: