background image

8695 6645 / C

 

B - SAFETY INSTRUCTIONS

 

POSIMATIC PS08

 

 

B-3 

 

 

Ensure that the equipment's working cannot be jammed by tools 
and/or objects left near moving parts, or by rotating pieces which 
could hit fixed parts (ground, stands, posts, workshop frames, etc.).  

Imperative: 

an operator corridor must be clear over a minimum width 

of 800 mm according to safety standard NF EN 547-1 -3. 

 

 

Never use the positioner table as a sheet metal working table or 
heat the workpiece without taking basic precautions.

 

 

 

Dans le cas d’une utilisation pour opération de soudage, 
s’assurer que la masse du générateur est bien raccordée à la 
pièce avant de lancer le procédé.

 

 

 

If the equipment is used for welding, make sure that the ground 
of the power source is connected to the piece before you start 
welding. 

 

 

 

Never modify the machine.

 The positioner 

is not

 designed for 

anchoring or lifting equipment 

 

 

 

The use of Personal Protective Equipment (PPE) is 

mandatory

 

 

Clean the working area from time to time.  

 

 

Machine 

maintenance 

must be carried out 

with all the energy 

supplies switched off. 

The disconnection and padlocking of all 

energy sources is 

mandatory

 

 

3 - IMPORTANT

 

RECOMMENDATIONS 

 
 

 

When starting-up or when changing a connection, there is one chance 
in two that the connection of phases will be inverted, in which case the 
tilt limit switches become totally ineffective and there are great risks of 
damage (refer to chapter page D17). 

 
 

Summary of Contents for 95032111NG





































Reviews: