background image

A-10

INSTALLATION

MODULAR FUME HOOD

MODULAR FUME HOOD XL;

DOUBLE COMPARTMENT:

For double compartment hoods, do not
make cut-outs on both corners of the 
“A-TOP” and “C-BOTTOM END” panels.
Review the “A-TOP” and “C-BOTTOM
END” panel lay-out and cut only on the required corners.
Corner cutting is not required for the panel assembled
adjacent to the T-brackets.

a) Follow steps 1 to 3 as per single compartment

In case of Modular Fume Hood XL/standing:

Mount connection plates (2 plates on each on all four corners) of
corner reinforcement set on the main profiles using self-tapping
screws. See Figure A.15.

FIGURE – A.15

b) Mount a T-bracket on the main frame profile. See Figure A.16 

c) Determine the right distance between the profiles by means

of a long H-profile. See Figure A.17.

d) Mount two cross profiles on T-bracket. See Figure A.17.

e) Place the other T-bracket on the loose side of cross-profiles

to keep them together. Do not fasten the screws yet. See
Figure A.17.

f)

Make sure the cross-profiles are precisely square (90°) to the

main frame profile. See Figure A.17.

g) Finish the entire compartment (except for the last “A-TOP”

roof panel) before continuing with the next compartment. See
Figure A.17 and Figure A.12. Follow steps 4 to 18 as per
single compartment

h) Use a cargo lashing (1) around the end of the profiles to keep

them in the right position. 

i)

Fasten the T-bracket to the cross profiles and the main frame

profile.

j)

Follow steps 19 and 20 as per single compartment

A

XL

mm

inch

A

450

17.7

10 mm

ATTENTION

Summary of Contents for Modular Fume Hood





























Reviews: