INSTALLATION
A-4
A-4
SAE-400 SEVERE DUTY
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Section
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC
Return
to
Master
T
OC
HIGH ALTITUDE OPERATION
At higher altitudes, output derating may be necessary.
As a rule of thumb, derate the welder output 5% for
every 500 meters (1640 ft.) above 1000 meters (3280
ft.).
Contact a Perkins Service Representative for any
engine adjustments that may be required for high alti-
tude operation.
TOWING
The recommended trailers for use with this equipment
for in-plant and yard towing by a vehicle
(1)
are Lincoln’s
K767-1 and K956-1. The K956-1 is also designed to be
used at highway speeds
(1)
.If the user adapts a non-
Lincoln trailer, he must assume responsibility that the
method of attachment and usage does not result in a
safety hazard or damage the welding equipment.
Some of the factors to be considered are as follows:
1. Design capacity of trailer vs. weight of Lincoln
equipment and likely additional attachments.
2. Proper support of, and attachment to, the base of
the welding equipment so that there will be no
undue stress to the trailer’s framework.
3. Proper placement of the equipment on the trailer to
insure stability side to side and front to back when
being moved and when standing by itself.
4. Typical conditions of use, such as travel speed,
roughness of surface on which the trailer will be
operated, and environmental conditions.
5. Proper preventative maintenance of trailer.
6. Conformance with federal, state and local laws.
1
(1)
For highway use, consult applicable federal, state
and local laws regarding specific requirements for
use on public highways, such as brakes, lights, fend-
ers, etc.
VEHICLE MOUNTING
Improperly mounted concentrated loads may cause
unstable vehicle handling and tires or other compo-
nents to fail.
• Only transport this equipment on serviceable vehi-
cles which are rated and designed for such loads.
• Distribute, balance and secure loads so vehicle is
stable under conditions of use.
• Do not exceed maximum rated loads for compo-
nents such as suspension, axles and tires.
• Mount equipment base to metal bed or frame of
vehicle.
• Follow vehicle manufacturerʼs instruction.
----------------------------------------------------------------------------
PRE-OPERATION ENGINE SERVICE
READ the engine operating and maintenance instruc-
tions supplied with this machine.
ENGINE OIL
The engine is shipped with the engine crankcase filled
with high quality SAE 10W-30 oil (API class CD or bet-
ter). Check the oil level before starting the engine. If it is
not up to the full mark on the dip stick, add oil as required.
Check the oil level every four hours of running time during
the first 35 running hours. Refer to the engine Operator’s
Manual for specific oil recommendations and break-in
information. The oil change interval is dependent on the
quality of the oil and the operating environment. Refer to
the engine Operator’s Manual for the proper service and
maintenance intervals.
FUEL USE DIESEL FUEL ONLY
Fill the fuel tank with clean, fresh diesel fuel.
The capacity of the fuel tank is 22.5 gallons (85.1 liters).
See engine Operator’s Manual for specific fuel recom-
mendations.
NOTE:
Before attemting to start the engine, be sure the
fuel shutoff valve is open.
WARNING
• Stop engine while fueling.
• Do not smoke when fueling.
• Keep sparks and flame away
from tank.
• Do not leave unattended while
fueling.
• Wipe up spilled fuel and allow
fumes to clear before starting
engine.
• Do
not
overfill
tank,
fuel
expansion may cause over-
flow.
DIESEL FUEL ONLY
------------------------------------------------------------------------
WARNING
DIESEL FUEL
can cause fire.
