Lincoln Electric VANTAGE SVM178-B Service Manual Download

Page: 67 / 278

ACCESSORIES

C2.3

VANTAGE® 500

TIG OPTIONS

K1783-9 PTA-26V TIG Torch

Air Cooled 200 amp torch (2 piece) equipped with valve
for gas flow control. 25 ft. (7.6m) length.

KP509 Magnum Parts Kit for PTA-26V TIG Torch

Magnum  Parts  Kit  provides  all  the  torch  accessories
you  need  to  start  welding.    Parts  kit  provides  collets,
collet  bodies,  a  black  cap,  alumina  nozzles  and  tung-
stens in a variety of sizes, all packaged in an easy to
carry reclosable sack.

K870 Foot Amptrol®-

Varies current while welding for

making critical TIG welds and crater filling. Depress
pedal to increase current. Depressing pedal fully
achieves maximum set current. Fully raising the pedal
finishes the weld and starts the after flow cycle on sys-
tems so equipped. Includes 25 ft. (7.6m) control cable.

K963-3 Hand Amptrol®-

Varies current for making crit-

ical TIG welds. Fastens to the torch for convenient
thumb control. Comes with a 25 ft. (7.6m) cable. (One
size fits all Pro-Torch TIG Torches.)

K2347-1 Precision TIG 185 Ready-Pak

For  AC TIG  Welding  with  square  wave  performance
use  the AC generator  of  the  Engine-Driven  Welder  to
supply  the  power.    Easy  setup.    Includes  torch,  foot
amptrol, gas regulator and hose.  Requires the K1816-
1 Full KVA adapter kit.

K2350-1 Invertec® V205-T AC/DC One-Pak™ Package

For  AC TIG  welding  with  square  wave  performance,
use  the  AC  generator  of  the  engine-driven  welder  to
supply  the  power.    Easy  setup.    Includes  torch,  parts
kit, regulator and hose kit, Twist-Mate™ torch adapter,
work cable with Twist-Mate end and foot Amptrol®.

HIGH FREQUENCY GENERATORS FOR
TIG APPLICATIONS

The K799 Hi-Freq Unit and the K930- [ ] TIG Modules
are suitable for use with the Vantage 500.  The Vantage
500 is equipped with the required RF bypass circuitry
for the connection of high frequency generating equip-
ment.    The  high  frequency  bypass  network  supplied
with  the  K799  Hi-Freq  Unit  does  NOT  need  to  be
installed into the Vantage 500.

The  Vantage  500  and  any  high  frequency-generating
equipment must be properly grounded.  See the K799
Hi-Freq  Unit  and  the  K930-AII  TIG  Module  operating
manuals for complete instructions on installation, oper-
ation, and maintenance.

WIRE FEEDER OPTIONS

K449 LN-25 Wire Feeder

Portable CC/CV unit for flux-cored and MIG welding.
Includes Gas Solenoid & Internal Contactor.

K126-2 Magnum® 350 Innershield Gun (for LN-25)

For self-shielded wire with 15 ft. (4.5m) cable. For
.062-3/32” (1.6-2.4mm) wire.

KP653-3/32 Drive Roll and Guide Tube Kit (for LN-25)

For .068-3/32” (1.8-2.4mm) cored or solid steel wire.

K1802-1 Magnum® 300 MIG Gun

For .035-.045 (0.9-1.2mm) gas shielded wire. Includes
15 ft. gun and cable assembly and connector kit.

KP653-035S Drive Roll and Guide Tube Kit (for LN-25)

For .035-.040” (0.9-1.0mm) solid steel wire.

K2613-1 LN-25 PRO PORTABLE WIRE FEEDER-

The

MAXTRAC® wire drive enhances performance, while the
replacement case, and many other upgrade options that can
be installed in less then five minutes aid in the serviceability.

KP1697-5/64 Drive Roll Kit-

Includes: 2 polished U

groove drive rolls, outer wire guide and inner wire guide
for solid core wire. (Used on LN-25 Pro)

KP1697-068 Drive Roll Kit-

Includes: 2 polished U

groove drive rolls, outer wire guide and inner wire guide
for solid core wire. (Used on LN-25 Pro)

KP1696-1 Drive Roll Kit-

Includes: 2 V groove drive

rolls and inner wire guide for Steel Wires. (Used on LN-
25 Pro)

K487-25 Magnum SG Spool Gun

Hand held semiautomatic wire feeder. Requires SG
Control Module and Input Cable.

K488 SG Control Module