background image

 

 

DTF – 1960 Series Operator Manual 

IMPORTANT WARNING AND SAFETY INFORMATION 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

•  Minimum clearances must be maintained from all walls and combustible materials. 
•  Keep the appliance area free and clear of combustible material. 
•  Adequate clearance for air openings to the control chamber on both sides of the appliance is required. 
•  Do not obstruct the ventilation holes in the control boxes and covers as these provide cooling air for the controls. 
•  The appliance is to be operated only on the type of electricity as shown on the specification plate. 
•  This manual should be retained for future reference. 
•  The electrical wiring diagram is located under the control box cover. 
•  The fixed supply wiring insulation must be protected against high interior surface temperatures. 
 
 

BEFORE INSTALLATION 

 

Upon receipt of this unit, immediately unpack and remove any protective packaging to inspect for possible 
concealed shipping damage.  If unit is found to be damaged, save all packing materials and contact your delivery 
carrier within 5 days.  If there is apparent damage: 

 

United States and Canada: Arrangements should be made to file a claim against the carrier as Interstate 
Commerce Regulations require that the claim must be initiated by the consignee. 
 
Other Countries:  Freight terms will be developed and extended on an individual basis. 
 
Proper and secure storage facilities should be arranged for the unit(s), if necessary, to protect against outdoor or 
damp conditions at all times before installation.  Failure to follow these instructions will negate Lincoln Foodservice 
Product’s or your ability to file claims and receive compensation for shipping damage. 
 

This manual contains important safety and installation-operation instructions.  Require all operators to 
read this manual thoroughly before installing, operating or servicing this equipment.  Improper 
installation, adjustment, alteration, service or maintenance can cause property damage, injury or 
death.  

 

 

  WARNING:

 

!

 

Do not work around conveyor belt with long hair, loose clothing, or dangling jewelry.  Getting caught in the 
belt could result in serious injury. 

 

 

DANGER! 

!

 

For your safety, do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or 
any other appliance. 

 

 

DANGER! 

!

 
Do not spray aerosols in the vicinity of this appliance while it is in operation. 

 

 

DANGER! 

!

 

If the power supply cord appears to be damaged, do not attempt to operate the unit.  Contact a service 
agent or qualified electrician to repair! 

 

 

DANGER! 

!

 

Do not use parchment paper when placing food product through the appliance!  Use of such materials 
may cause a fire and should never be placed in the appliance. 

 

 

DANGER! 

!

Summary of Contents for 1960 Series





















Reviews:

Related manuals for 1960 Series