background image

 

LBDG-250-DC-8200-1 

 

 

IMPORTANT SAFETY AND INSTALLATION WARNINGS 

 

WARNING:

  DO  NOT  ATTEMPT  TO  SERVICE  THIS  PRODUCT 

YOURSELF  AS  OPENING  OR  REMOVING  COVERS  MAY  EXPOSE 
YOU  TO  DANGEROUS  VOLTAGES  OR  OTHER  HAZARDS.  REFER 
ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.  

 
MOUNTING:

 

Mount  this  product  only  as  described  in  the  installation  instructions, 
otherwise  it  may  fall  causing  serious  personal  injury  and/or  damage  to 
the device. Use only the brackets supplied with the product. Do not use 
attachments  not  recommended  for  this  product  as  they  may  cause 
hazards.

 

 
SERVICING:

 

Remove  power  from  this  device  and  refer  servicing  to  qualified 
personnel under the following conditions:  

1.  If the inside of the station has been exposed to rain or water.  
2.  If  the  station  does  not  operate  normally  by  following  the 

operating  instructions.  Adjust  only  those  controls  that  are 
covered  by  the  operating  instructions  as  an  improper  adjustment 
may  result  in  damage  and  will  often  require  extensive  work  by  a 
qualified technician to restore the unit to its normal operation.  

3.  If the unit has been dropped or the chassis has been damaged.  
4.  If the unit exhibits a distinct change in performance.  

 

 
 
 
 
 

Summary of Contents for LBDG-250-DC-8200-1














Reviews: