62
DO1052DV
CZ
· Na dveře si našroubujte madlo na otevírání (viz obrázek).
16
· Jakmile mrazničku usadíte na místo, nechte ji ještě 8 hodiny stát v klidu než ji zapnete, aby se usadilo
chladící médium.
· Po zapnutí bude přibližně 24 hodin trvat, než se uvnitř mrazáku nachladí požadovaná teplota.
PŘEHOZENÍ DVEŘÍ
Tato mraznička má dveře, které se dají přehodit a otevírat na opačnou stranu. Pokud je chcete přehodit a
přešroubovat panty, zavolejte odborný servis nebo se alespoň zeptejte zkušeného technika.
Před začátkem úpravy dveří musí být mraznička prázdná a vypojená z el. sítě.
Odšroubujte 2 šrouby z horní strany krytu.
1.
Vyšroubujte oba šroubky v zadní části krytu mrazáku.
Reverse Door
Tool required:
Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
Ensure the unit is unplugged and empty.
To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
All parts removed must be saved to do the reinstallation of the door.
Do not lay the unit flat as this may damage the coolant system.
It
'
s
better
that
2
people
handle
the
unit
during
assembly
.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew
2.
Odejměte horní kryt mrazáku.
Reverse Door
Tool required:
Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
Ensure the unit is unplugged and empty.
To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
All parts removed must be saved to do the reinstallation of the door.
Do not lay the unit flat as this may damage the coolant system.
It
'
s
better
that
2
people
handle
the
unit
during
assembly
.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew
3.
Odšroubujte šroubky, které drží horní pant dveří. Dveře nadzvedněte a položte je na měkký povrch,
tak aby se nepoškrábaly.
Reverse Door
Tool required:
Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
Ensure the unit is unplugged and empty.
To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
All parts removed must be saved to do the reinstallation of the door.
Do not lay the unit flat as this may damage the coolant system.
It
'
s
better
that
2
people
handle
the
unit
during
assembly
.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew
Summary of Contents for Domo DO1052DV
Page 77: ...77 DO1052DV www domo elektro be SK ...
Page 78: ...78 DO1052DV ...
