25
DO9248J
www.domo-elektro.be
DE
GEBRAUCH
MONTAGE
1.
Stellen Sie sicher, dass der Stecker nicht eingesteckt ist, und dass der Ein-/Ausschalter auf „Aus“
steht, bevor Sie das Gerät zusammenbauen.
2.
Stellen Sie die Motoreinheit auf eine stabile, ebene Arbeitsfläche.
3.
Drehen Sie die Schüssel um. Am Auslauf für Fruchtfleisch sehen Sie eine kleine Gummi-Platte.
Sicherstellen, dass diese Pufferplatte an der Unterseite der Schüssel in die korrekte Position im
Auslauf für Fruchtfleisch gelegt wird.
4.
Setzen Sie die Schüssel auf die Basis mit Motor. Stellen Sie sicher, dass die Schüssel gut auf der
Achse des Motorblocks sitzt und dass der Auslauf für Fruchtfleisch richtig positioniert ist.
5.
Setzen Sie das gewünschte Sieb in die Schüssel (das Sieb mit kleinen Löchern für Saft, das Sieb
mit größeren Löchern für Marmelade/Konfitüre oder das Sieb für gefrorene Speisen, d. h. für
tiefgefrorene Bananen und/oder Heidelbeeren, die zuvor so weit aufgetaut wurden, dass man mit
einer Gabel hineinstechen kann).
6.
Drehen Sie die Press-Schnecke in der Mitte der Schüssel fest. Stellen Sie sicher, dass sie gut
einrastet, andernfalls schließt der Deckel nicht.
7.
Setzen Sie den Deckel auf die Schüssel und stellen Sie sicher, dass das Symbol “
” auf
dem Deckel mit dem Symbol “
” der Schüssel übereinstimmt und drehen Sie den Deckel
dann im Uhrzeigersinn, bis das Symbol “
” des Deckels mit dem Symbol “
” der Schüssel
übereinstimmt. Drücken Sie dann den Klemmbügel nach oben, sodass der Deckel verriegelt wird.
Der Deckel muss richtig montiert werden, sonst wird das Gerät nicht funktionieren.
8.
Stecken Sie den Stopfer in den Fülltrichter des Deckels.
9.
Stellen Sie einen Messbecher unter den Auslauf für Saft und einen Messbecher unter den Auswurf
für Fruchtfleisch.
10. Öffnen Sie die Saftauslassabdeckung. Das Gerät ist jetzt einsatzbereit.
11. Wiederholen Sie diese Schritte in umgekehrter Reihenfolge, wenn Sie das Gerät wieder
auseinandernehmen.
3
6
4) Do not put overmuch materials in the juicer each time, therefore, the materials
with less moisture and hard fibre shall be put into the jar lid after being cut into
slices.
5) Do not put overmuch materials in the juicer each time, therefore, the materials
with less moisture and hard fibre shall be put into the jar lid after being cut into
slices.
6) Assemble the buffer plate well in position
The buffer plate shall be assembled well in the residue outlet after finish cleaning each
time.
ASSEMBLE YOUR SLOW JUICER
1. Put the jar downwards and make sure that the residue outlet shall be placed well in
position. The jar shall be assembled well in position properly otherwise the appliance will
not operate. Besides, before operating, please check the buffer plate and make sure that it
must be assembled well in the residue outlet (See Fig.2).
2. Then select the strainer based on your demand and then put it into the jar. There are
three strainers including juice strainer, jam strainer and frozen dish strainer for your
selection. After it, put the grinding head into the jar and ensure the grinding head is covered
well into the axis of the motor unit (see Fig.3).
NOTE:
The three strainers including juice strainer, jam strainer and frozen dish strainer
can not be exchanged with each other when operate. Juice strainer is used for extracting
Fig.2
6
4) Do not put overmuch materials in the juicer each time, therefore, the materials
with less moisture and hard fibre shall be put into the jar lid after being cut into
slices.
5) Do not put overmuch materials in the juicer each time, therefore, the materials
with less moisture and hard fibre shall be put into the jar lid after being cut into
slices.
6) Assemble the buffer plate well in position
The buffer plate shall be assembled well in the residue outlet after finish cleaning each
time.
ASSEMBLE YOUR SLOW JUICER
1. Put the jar downwards and make sure that the residue outlet shall be placed well in
position. The jar shall be assembled well in position properly otherwise the appliance will
not operate. Besides, before operating, please check the buffer plate and make sure that it
must be assembled well in the residue outlet (See Fig.2).
2. Then select the strainer based on your demand and then put it into the jar. There are
three strainers including juice strainer, jam strainer and frozen dish strainer for your
selection. After it, put the grinding head into the jar and ensure the grinding head is covered
well into the axis of the motor unit (see Fig.3).
NOTE:
The three strainers including juice strainer, jam strainer and frozen dish strainer
can not be exchanged with each other when operate. Juice strainer is used for extracting
Fig.2
4
6
4) Do not put overmuch materials in the juicer each time, therefore, the materials
with less moisture and hard fibre shall be put into the jar lid after being cut into
slices.
5) Do not put overmuch materials in the juicer each time, therefore, the materials
with less moisture and hard fibre shall be put into the jar lid after being cut into
slices.
6) Assemble the buffer plate well in position
The buffer plate shall be assembled well in the residue outlet after finish cleaning each
time.
ASSEMBLE YOUR SLOW JUICER
1. Put the jar downwards and make sure that the residue outlet shall be placed well in
position. The jar shall be assembled well in position properly otherwise the appliance will
not operate. Besides, before operating, please check the buffer plate and make sure that it
must be assembled well in the residue outlet (See Fig.2).
2. Then select the strainer based on your demand and then put it into the jar. There are
three strainers including juice strainer, jam strainer and frozen dish strainer for your
selection. After it, put the grinding head into the jar and ensure the grinding head is covered
well into the axis of the motor unit (see Fig.3).
NOTE:
The three strainers including juice strainer, jam strainer and frozen dish strainer
can not be exchanged with each other when operate. Juice strainer is used for extracting
Fig.2
7
juice,
jam strainer is used for making ketchup only
while frozen dish strainer is used for
making frozen dish. Select the appropriate strainer based on your demand.
3. Assemble the jar lid on the jar correctly. Firstly, put the jar lid downwards and then
make the symbol “ ” on the jar lid align with the symbol “
” on the jar and then rotate
the jar lid clockwise until the symbol “ ” on the jar lid aligns with the symbol “ ”on the
jar (See Fig.4).
After it, press the fastener inwards to lock the jar lid well in position. The
jar lid shall be assembled well in position properly otherwise the appliance will not operate.
Finally, put the food pusher into the jar lid.
Fig.3
Fig.4
5