42
DO927BFK
EN
Your appliance uses isobutane (R600a) as a refrigerant. Although R600a is an environmentally
friendly and natural gas, it is explosive. Therefore you should be careful during shipment and
installation to prevent your appliance’s cooler elements from being damaged. In the event of
a leak caused by damage to the cooler elements, move your fridge from open flame or heat
sources and ventilate the room where the appliance is located for a few minutes.
CLEANING
Do not use abrasive cleaning agents or solvents.
1. Disconnect the mains plug from the mains socket.
2. Take out the food and store in a cool location.
3. If necessary, defrost the refrigerator/freezer. To speed up the process, a pan of hot water
can be placed in the freezer.
4. Wipe the condensation off with a cloth or sponge.
5. Clean the appliance with a soft cloth, warm water and detergent.
6. Wipe the door seal with clear water only and then wipe dry thoroughly.
7. After cleaning reconnect and adjust the temperature control knob as desired.
8. Put the food back into the appliance.
DOOR CONVERSION
1. Remove the cover plate of the screws. Remove the three screws and then the upper
hinge that holds the door in place. Lift the door off and place it on a soft surface to
prevent scratching.
3. Take off the middle hinge by removing
the screws. Lift the lower door and place
it on a padded surface to prevent it from
scratching.
Remove the screws’ covers and place
them to the opposite side.
Swap the position of the plastic tube and
hole cover on top of the lower door.
Remove the door block, screw and plastic
tube under the lower door and move
them to the opposite side. You may
need to replace the door block to fit the
opposite side.
unscrew
Reversing the Door Swing
Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner
1. Take off the hinge cover.
2. Remove the the upper hinge. Lift the
upper door and place it on a padded
surface to prevent it from scratching.
Remove the door block, screw and plastic
tube under the upper door and move
them to the opposite side. You may
need to replace the door block to fit the
opposite side.
• Ensure the unit is unplugged and empty.
• All parts removed must be saved to do the reinstallation of the door.
• Do not lay the unit flat as this may damage the coolant system.
• We recommend that 2 people handle the unit during assembly.
• If you want to have the door swing reversed, we recommend that you contact a
qualified technician. You should only try to reverse the door yourself if you believe
that you are qualified to do so.
8
INSTALLATION
LFC60W16_IB_160201_grace.indd 8
1/2/16 10:43 am
3. Take off the middle hinge by removing
the screws. Lift the lower door and place
it on a padded surface to prevent it from
scratching.
Remove the screws’ covers and place
them to the opposite side.
Swap the position of the plastic tube and
hole cover on top of the lower door.
Remove the door block, screw and plastic
tube under the lower door and move
them to the opposite side. You may
need to replace the door block to fit the
opposite side.
unscrew
Reversing the Door Swing
Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner
1. Take off the hinge cover.
2. Remove the the upper hinge. Lift the
upper door and place it on a padded
surface to prevent it from scratching.
Remove the door block, screw and plastic
tube under the upper door and move
them to the opposite side. You may
need to replace the door block to fit the
opposite side.
• Ensure the unit is unplugged and empty.
• All parts removed must be saved to do the reinstallation of the door.
• Do not lay the unit flat as this may damage the coolant system.
• We recommend that 2 people handle the unit during assembly.
• If you want to have the door swing reversed, we recommend that you contact a
qualified technician. You should only try to reverse the door yourself if you believe
that you are qualified to do so.
8
INSTALLATION
LFC60W16_IB_160201_grace.indd 8
1/2/16 10:43 am
2. On the bottom of the door there is a door stop and a Teflon bush to guide the hinge.
Move this to the other side.
3. Take off the middle hinge by removing
the screws. Lift the lower door and place
it on a padded surface to prevent it from
scratching.
Remove the screws’ covers and place
them to the opposite side.
Swap the position of the plastic tube and
hole cover on top of the lower door.
Remove the door block, screw and plastic
tube under the lower door and move
them to the opposite side. You may
need to replace the door block to fit the
opposite side.
unscrew
Reversing the Door Swing
Tools required: Philips style screwdriver / Flat bladed screwdriver / Hexagonal spanner
1. Take off the hinge cover.
2. Remove the the upper hinge. Lift the
upper door and place it on a padded
surface to prevent it from scratching.
Remove the door block, screw and plastic
tube under the upper door and move
them to the opposite side. You may
need to replace the door block to fit the
opposite side.
• Ensure the unit is unplugged and empty.
• All parts removed must be saved to do the reinstallation of the door.
• Do not lay the unit flat as this may damage the coolant system.
• We recommend that 2 people handle the unit during assembly.
• If you want to have the door swing reversed, we recommend that you contact a
qualified technician. You should only try to reverse the door yourself if you believe
that you are qualified to do so.
8
INSTALLATION
LFC60W16_IB_160201_grace.indd 8
1/2/16 10:43 am
