49
DO987BFK
www.domo-elektro.be
EN
· Avoid direct sunlight and heat. Direct sunlight may affect the acrylic
coating. Heat sources nearby will cause higher electricity consumption.
· Avoid very moist places. Too much moisture in the air will cause frost to
from very quickly on the evaporator, and your refrigerator.
· Before connecting your refrigerator to the power supply, check that the
voltage stated on the rating label of your appliance corresponds to the
voltage in your home. A different voltage could damage the appliance.
· The appliance must be grounded. The manufacturer is not responsible
for damages that may occur as a result of usage without grounding.
· After installation, leave the freezer for 8 hours before turning it on. This
way the refrigerant can settle.
· Allow the appliance to run empty for 24 hours so the compartment can
cool to the appropriate temperature.
· This appliance is designed to operate in ambient temperature between
16°C and 38°C. If these temperatures are exceeded, i.e. colder or
warmer, the appliance will not operate correctly.
· The appliance may only be used indoors.
· The freezer makes noise when the compressor pumps the coolant. This is normal.
DOOR CONVERSION
If you need to hinge your door on the opposite side it is recommended that you call your local authorised
service agent to make this conversion or ask a technician. Before you reverse the door, you should ensure
the appliance is unplugged and empty.
After reversing the door, leave the appliance alone for 8 hours before switching it on. This allows the
coolant to set. We recommend using a slotted screwdriver, a Phillips screwdriver, and a wrench (not
included), as well as the components supplied below.
Hinge cover plate
,QVWDOODWLRQ
Door Reversibility
Left Aid-Closer on Upper Door x 1 Left Aid-Closer on Lower Door x 1
nscrew top hinge cover and disconnect connectors of door switch and harness.
2.Unscrew top hinge
3.Remove the pin with a screwdriver and filp the hinge bracket. Then refit the pin to hinge bracket
unscrew
screw
8
Top door stopper
,QVWDOODWLRQ
Door Reversibility
Left Aid-Closer on Upper Door x 1 Left Aid-Closer on Lower Door x 1
nscrew top hinge cover and disconnect connectors of door switch and harness.
2.Unscrew top hinge
3.Remove the pin with a screwdriver and filp the hinge bracket. Then refit the pin to hinge bracket
unscrew
screw
8
Bottom door stopper
,QVWDOODWLRQ
Door Reversibility
Left Aid-Closer on Upper Door x 1 Left Aid-Closer on Lower Door x 1
nscrew top hinge cover and disconnect connectors of door switch and harness.
2.Unscrew top hinge
3.Remove the pin with a screwdriver and filp the hinge bracket. Then refit the pin to hinge bracket
unscrew
screw
8
1.
Loosen the screws of the hinge cover plate and remove the plate. Disconnect both connectors of the
cables.
,QVWDOODWLRQ
Door Reversibility
Left Aid-Closer on Upper Door x 1 Left Aid-Closer on Lower Door x 1
nscrew top hinge cover and disconnect connectors of door switch and harness.
2.Unscrew top hinge
3.Remove the pin with a screwdriver and filp the hinge bracket. Then refit the pin to hinge bracket
unscrew
screw
8
y
y
,QVWDOODWLRQ
1007NN
1071NN
6SDFH5HTXLUHPHQW
Keep enough space of door open.
Keep at least 50mm gap at two sides.
To do this adjust the two levelling feet at front of the unit.
If the unit is not level, the doors and magnetic seal
alignments will not be covered properly.
/HYHOOLQJWKHXQLW
13
y
y
,QVWDOODWLRQ
1007NN
1071NN
6SDFH5HTXLUHPHQW
Keep enough space of door open.
Keep at least 50mm gap at two sides.
To do this adjust the two levelling feet at front of the unit.
If the unit is not level, the doors and magnetic seal
alignments will not be covered properly.
/HYHOOLQJWKHXQLW
13
Summary of Contents for DOMO DO987BFK
Page 114: ...114 DO987BFK...
Page 115: ...115 DO987BFK www domo elektro be...
