background image

 

 

 

This  equipment  has  been  tested  and  found  to  comply  with  the 

limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 
These  limits  are  designed  to  provide  reasonable  protection  against 
harmful  interference  in  a  residential  installation.  This  equipment 
generates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not 
installed and used in accordance with the instructions, may cause harmful 
interference  to  radio  communications.  However,  there  is  no  guarantee 
that interference will not occur in a particular installation. If this equipment 
does  cause  harmful  interference  to  radio  or  television  reception,  which 
can  be  determined  by  turning  the  equipment  off  and  on,  the  user  is 
encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the 
following measures: 

—Reorient or relocate the receiving antenna. 

—Increase the separation between the equipment and receiver. 

—Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected. 

—Consult the dealer or an experienced radio/TV technician for help. 

 

CAUTION: Use shielded cables to connect this device to computers. 

Any  changes  or  modifications  not  expressly  approved  by  the  grantee  of 
this device could void the user’s authority to operate the equipment. 

 

 

 

 

 
 
 
 
 

Summary of Contents for Infinea Tab 4
















Reviews: