background image

Linear Acoustic LA-5180 Metadata Frame Sync/Generator Operation Manual

Metadata

43

Speech

Max Boost: 15 dB (below -50 dB)

Boost Range: -50 dB to -31 dB (5:1 ratio)

Null Band Width: 5 dB (-31 dB to -26 dB)

Early Cut Range: -26 dB to -16 dB (2:1 ratio)

Cut Range: -16 dB to +4 dB (20:1 ratio)

None

No DRC profile selected. The dialogue level parameter (dialnorm) is still applied

NOTE:

Protection DRC is still active in “None” mode

These choices are available to the content producer for both Line Mode and RF Mode. 
The content producer chooses which of these profiles to assign to each mode; when the 
consumer or decoder selects a DRC mode (i.e. apply DRC fully, not at all, or anywhere in-
between), the profile chosen by the producer is applied.

Note that the DRC profile is a choice available only when setting up metadata, and is used 
by the emission encoder to guide its generation of the actual Line Mode and RF Mode gain 
control values (dynrng and compr, respectively). Once the profile is set and is used by the 
encoder, the only information available in the metadata stream are these gain control val-
ues. Importantly, these gain control values can be extracted and displayed in the form of a 
gain reduction/expansion meter a very useful tool available in the Linear Acoustic LAMB-
DA and Dolby DM100, DP564, and LM100 products.

In addition to the DRC profile, metadata can limit signal peaks to prevent clipping during 
downmixing. This metadata, known as overload protection, is inserted by the encoder only 
if necessary. For example, consider a 5.1-channel program with signals at digital full scale 
on all channels being played through a stereo, downmixed line-level output. Without some 
form of attenuation or limiting the output signal would obviously clip. Correct setting of 
the dialogue level and DRC profiles normally prevents clipping and unnecessary applica-
tion of overload protection. 

Summary of Contents for MetaMAXLA-5180























































Reviews: