background image

 

 

 

 

MODEL 502HV

©

 

(1996 - MSRP $1099)

 

 

OWNER'S MANUAL AND

 

INSTALLATION GUIDE

 

 

502HV

©

 COMPETITION CHALLENGER

 

A new approach in competition amplifiers is here...The 

LINEAR POWER™

 

502HV

©

 amplifier is a 25-watt per channel amplifier with extremely low distortion 

and lots of dynamic headroom. We have utilized 

TO-3

 transistors throughout the 

amplifier for the highest reliability and unmatched sound quality. 

LINEAR POWER™

 designers and engineers listened to the suggestions of 

seasoned competitors to find the right foundation for this amplifier. We chose an 
amplifier that has been tried and tested in challenging situations. We then took 
the next step of deciding on an operating format that went against conventional 
competition designs. 

LINEAR POWER™

 engineers were convinced that the 

HV

©

 

(

HIGH VOLTAGE)

 competition amplifier would be much more stable and 

controllable, establishing high damping factor and unmatched dynamic 
headroom, than ANY high current design amp. Distortion at rated power is 
extremely low and the unregulated power supply is capable of delivering serious 
output when needed - 

NOT to extremely low impedances

 - 

but to higher 

impedances where sound quality can be assured

. This can be done due to 

the extreme 

HIGH VOLTAGE

 design of the 

HV

©

 amplifier. There is no need to 

have low impedance loads to stress the amplifier to make power. The minimum 
operating impedance of the 

502HV

©

 is 

2 ohms stereo

 or 

4 ohms mono

eliminating the need for multiple drivers to lower the impedance load to get 
maximum power output. A benefit of 

HIGH VOLTAGE

 design is less heat and 

lower current draw from your electrical system, at the same time, delivering the 
power that you want. 

Features include the 

LINEAR POWER™ DYNAMICS IMPROVING 

PROCESSOR

©

 or 

D.I.P. "Bass Boost" switch, which adds 

6dB

 of gain at 

45 Hz

 

for that additional 'OOMPH', if needed. The 

502HV

©

 also has an inverted channel 

so that the amp will bridge without he use of an internal bridge switch or external 
bridging module. This inverted channel also allows the 

502HV

©

 to play in 

stereo/mono mode simultaneously. With all the 

502HV

©

 delivers, it could be the 

final element needed to dominate competitions. 

 

F   O    R        T    H    E      L    O     V    E     O     F     M     U     S     I    C  

™ 

 

© 2008 Linear Power, Inc. - ALL RIGHTS RESERVED 

LINEAR POWER

 is a trademark of Linear Power, Inc. 

1

Summary of Contents for 502HV






Reviews: