background image

1

dc1763af

DEMO MANUAL DC1763A

 DESCRIPTION

LTC2195, LTC2194, LTC2193, 

LTC2192, LTC2191, LTC2190 

16-Bit, 25Msps to 125Msps Dual ADCs

Demonstration circuit 1763A supports a family of 16-Bit 
25Msps to 125Msps ADCs. Each assembly features one 
of the following devices: LTC

®

2195, LTC2194, LTC2193, 

LTC2192, LTC2191, LTC2190 high speed, dual ADCs.

The versions of the 1763A demo board are listed in Table 1. 
Depending on the required resolution and sample rate, 
the DC1763A is supplied with the appropriate ADC. The 

L

, LT, LTC, LTM, μModule, Linear Technology and the Linear logo are registered trademarks 

and PScope is a trademark of Linear Technology Corporation. All other trademarks are the 
property of their respective owners.

circuitry on the analog inputs is optimized for analog input 
frequencies from 5MHz to 140MHz. Refer to the data sheet 
for proper input networks for different input frequencies.

Design files for this circuit board are available at 
http://www.linear.com/demo

Table 1. DC1763A Variants

DC1763A VARIANTS

ADC PART NUMBER

RESOLUTION

MAXIMUM SAMPLE RATE

INPUT FREQUENCY

1763A-A

LTC2195

16-Bit

125Msps

5MHz to 140MHz

1763A-B

LTC2194

16-Bit

105Msps

5MHz to 140MHz

1763A-C

LTC2193

16-Bit

80Msps

5MHz to 140MHz

1763A-D

LTC2192

16-Bit

65Msps

5MHz to 140MHz

1763A-E

LTC2191

16-Bit

40Msps

5MHz to 140MHz

1763A-F

LTC2190

16-Bit

25Msps

5MHz to 140MHz

PERFORMANCE SUMMARY

(T

A

 = 25°C)

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Supply Voltage – DC1763A

Depending on Sampling Rate and the A/D Converter 
Provided, this Supply Must Provide up to 500mA.

3

3.6

6

V

Analog Input Range

Depending on SENSE Pin Voltage

1

2

V

P-P

Logic Input Voltages

Minimum Logic High
Maximum Logic Low

1.3
0.6

V
V

Logic Output Voltages (Differential)

Nominal Logic Levels (100Ω Load, 3.5mA Mode)
 Common 

Mode

Minimum Logic Levels (100Ω Load, 3.5mA Mode)
 Common 

Mode

350

1.25

247

1.25

mV

V

mV

V

Sampling Frequency (Convert Clock Frequency)

See Table 1

Encode Clock Level

Single-Ended Encode Mode (ENC

 Tied to GND)

Differential Encode Mode (ENC

 Not Tied to GND)

0

0.2

3.6
3.6

V
V

Resolution

See Table 1

Input Frequency Range

See Table 1

SFDR

See Applicable Data Sheet

SNR

See Applicable Data Sheet

Summary of Contents for DC1763A












Reviews: