background image

Limited Two-Year Warranty* 

1.  Your  new  product  is  covered  by  a  limited  two-year  warranty 

against defects in material and workmanship. Any repairs 

required will be made at no charge within the first two years after 

purchase as a new unit. 

2. Any units returned for warranty repair must be shipped prepaid 

after  receiving  return  authorization.  If  possible,  the  unit  should  be 

shipped  in  its  original  packaging.  If  such  is  not  possible,  the  unit 

should be well packed with particular attention paid to protection 

of all corners and avoidance of any looseness in the carton.  

3. This warranty does not apply to damage resulting from physical 

abuse or unauthorized alterations or repairs, or from tube rolling or 

adapter  use,  or  from  the  use  of  third-party  components,  or 

damage to exterior finish resulting from careless use.  

4.  The  warranty  is  void  if  the  serial  number  has  been  removed, 

altered, or defaced. 

5. This warranty is void if improper voltage is applied to any input or 

output. 

6.  If  Linear  Tube  Audio  determines  after  receiving  the  unit  that 

damage was misrepresented and has been caused by something 

not  covered  by  the  warranty,  the  customer  must  pay  for  any 

necessary repairs before the unit is returned to the customer. 

7.  Linear  Tube  Audio  reserves  the  right  to  improve  or  change  its 

products  without  obligation  to  modify  previously  manufactured 

units. 

* Applicable for domestic sales only. There is a one year warranty 

for  overseas  customers.  Handling  and  shipping  costs  are  the 

responsibility of the overseas customer. 

Service Note 

ZOTL amplifiers use a unique circuit and even trained technicians 

familiar  with  tube  amplifiers  may  not  know  how  to  correctly  work 

on  LTA  products.  Please  contact  us  before  attempting  any 

alteration  or  repair,  whether  you  are  concerned  about  the 

warranty or not.

Summary of Contents for ZOTL40 Reference









Reviews: