Linear ADT Pulse GD00Z-2 Installation Instructions Manual Download

Page: 5 / 16

GD00Z-2

GARAGE DOOR

CONTROLLER

POWER

INPUT

JACK

WARNING

LIGHT

INCLUDE

BUTTON

CONNECTION

WIRES

MOUNTING SCREWS

AND ANCHORS

FOR GD00Z-2

POWER

SUPPLY

TILT

SENSOR

STATUS

INDICATOR

OPTIONAL

ADJUSTABLE

GD00Z-2 MOUNTING

BRACKET

POWER

SUPPLY

RETAINING

BRACKET

SCREWS AND

MOUNTING TAPE

FOR TILT SENSOR

SCREW AND

MOUNTING HARDWARE

FOR ADJUSTABLE

BRACKET

SCREW FOR

POWER SUPPLY

BRACKET

The Garage Controller System

The GD00Z-2 System consists of three major components:

•

The Controller

— The Controller wires to the garage door opener’s pushbutton terminals, receives

door status from the tilt sensor, and communicates with the ADT Pulse system.

•

The Tilt Sensor

— The battery powered Tilt Sensor monitors the position of the garage door and

sends the status to the Controller.

•

The Power Supply

— The Power Supply provides low voltage power to the Controller.

Package Contents

Figure 2. Package Contents

Summary of Contents for ADT Pulse GD00Z-2
















Search results

Summary of Contents for ADT Pulse GD00Z-2

Reviews:

Related manuals for ADT Pulse GD00Z-2

Brands by name

Popular brands

Linear ADT Pulse GD00Z-2, Installation Instructions Manual

Search results

Summary of Contents for ADT Pulse GD00Z-2

Reviews:

Related manuals for ADT Pulse GD00Z-2

Brands by name

Popular brands