VS-GSWG Swing Gate Operator Installation Guide
- 14 -
P1250 Revision X6 7-8-2011
Advanced Controller Programming
Entering Advanced Programming Mode
To access and program the Advanced Programming functions, for each
programming session, Advanced Programming must be enabled.
After exiting programming, the Advanced Programming functions
will be available on the programming display during the next
programming session unless the operator has run 50 or more
cycles. After that, Advanced Programming must be enabled again.
Maximum Run Time
The factory default for the Maximum Run Time (MRT) is 99 seconds.
When the operator starts, a timer will begin counting. If a open or close
limit is not reached or an obstacle or reversing input is not received
before the timer expires, the operator will stop, the unit locks out and the
alarm sounds. The timer can be set for 10 to 99 seconds, but should be
left at 99 in most applications. Setting it too close to the actual run time
may cause the time to expire with changing ambient temperature, gate
conditions, etc…
If AC is present and an open or close limit is not reached or an obstacle
or reversing input is not received before this timer exceeds MRT, the
operator will stop, the unit locks out and the alarm sounds.
Single Button Input Setup
This function is used for selecting the operation for single button controls
and radio receivers.
The factory default sets the
SINGLE
input terminal so successive inputs
will cycle the operator in OPEN-STOP-CLOSE-STOP order.
Alternately, the
SINGLE
input can be set to cause the gate to OPEN
unless the gate is fully open. If the gate is fully open, the input will cause
the gate to CLOSE.
Stagger Mode
This function is used in dual gate installations only.
The factory
default sets the Stagger Mode to OFF. In dual gate installations the
two operators communicate through the 3-wire
COMM LINK
interface.
When using the Stagger Mode, set one operator for delayed opening and
the other operator for delayed closing. The Stagger Time programming
function (see below) sets the length of the delay.
✓
NOTE:
This function will only be displayed if dual gate operation is
selected.
Stagger Delay Time
This function is used in dual gate installations only.
The factory
default sets the Stagger Time to 0 seconds (OFF). The Stagger Time
sets the delay for the Stagger Mode. The Stagger Delay Time can be set
from 1-99 seconds.
✓
NOTE:
This function will only be displayed if dual gate operation is
selected.
FUNCTION
ADVANCED P
R
O
GR
AMMIN
G
FUNCTION
S
WILL NOT
B
E DI
S
PLAYED
OPTIONS
P
R
E
SS
UP O
R
DOWN TO CYCLE
TH
R
OU
G
H OPTION
S
P
R
E
SS
ENTE
R
TO
S
ELECT AN OPTION
ADVANCED
PROGRAMMING
"AD"
ADVANCED P
R
O
GR
AMMIN
G
OPTION
S
WILL
B
E DI
S
PLAYED
NOTE
:
ADVANCED PROGRAMMING
WILL STAY ENABLED AFTER
EXITING PROGRAMMING UNTIL
THE GATE CYCLES 50 TIMES
FUNCTION
S
IN
G
LE INPUT WILL OPEN OPE
R
ATO
R
,
IF OPE
R
ATO
R
I
S
AL
R
EADY OPEN,
S
IN
G
LE
INPUT WILL CLO
S
E OPE
R
ATO
R
S
IN
G
LE INPUT WILL CYCLE OPE
R
ATO
R
IN O
R
DE
R
OF OPEN-
S
TOP-CLO
S
E-
S
TOP
OPTIONS
P
R
E
SS
UP O
R
DOWN TO CYCLE
TH
R
OU
G
H OPTION
S
P
R
E
SS
ENTE
R
TO
S
ELECT AN OPTION
SINGLE BUTTON
INPUT SETUP
"SB"
FUNCTION
S
ET
S
THI
S
OPE
R
ATO
R
FO
R
DELAYED OPEN
DI
S
A
B
LE
S
S
TA
GG
E
R
FUNCTION
S
ET
S
THI
S
OPE
R
ATO
R
FO
R
DELAYED CLO
S
E
OPTIONS
P
R
E
SS
UP O
R
DOWN TO CYCLE
TH
R
OU
G
H OPTION
S
P
R
E
SS
ENTE
R
TO
S
ELECT AN OPTION
STAGGER
MODE
"SM"
DUAL GATES
ONLY
FUNCTION
S
ET
S
TA
GG
E
R
DELAY VALUE
1 TO
99
S
ECOND
S
S
TA
GG
E
R
TIME
R
DI
S
A
B
LED
OPTIONS
P
R
E
SS
UP O
R
DOWN TO CYCLE
TH
R
OU
G
H OPTION
S
P
R
E
SS
ENTE
R
TO
S
ELECT AN OPTION
STAGGER
DELAY TIME
"ST"
DUAL GATES
ONLY
FUNCTION
P
R
E
SS
ENTE
R
FO
R
1
S
ECOND
WHILE DI
S
PLAY I
S
FLA
S
HIN
G
, P
R
E
SS
UP O
R
DOWN TO CHAN
G
E THE
MAXIMUM
R
UN TIME (10-
99
S
ECOND
S
)
OPTIONS
MAXIMUM RUN
TIMER
DI
S
PLAY
S
HOW
S
CU
RR
ENT
MAXIMUM
R
UN TIME
S
ETTIN
G
ENTER
ENTER
P
R
E
SS
ENTE
R
TO
S
TO
R
E THE VALUE
"RT"
