VS-GSWG Swing Gate Operator Installation Guide
- 16 -
P1250 Revision X6 7-8-2011
Advanced Controller Programming (Cont.)
Reset Cycle Count
The Controller counts of the number of times the operator has been
cycled full open and close. The cycle count can be displayed. The display
will scroll the cycle count number, fl ashing two digits at a time from left
to right.
To reset the Cycle Count, press and hold the
ENTER
button for 2 seconds
while the Cycle Count is displayed.
If the Maintenance Alert has been triggered, resetting the Cycle Count
will also reset the Maintenance Alert indicator.
Maintenance Alert Trigger
The Controller has a
MAINT ALERT
indicator that can be programmed
to light when the number of activations exceeds a set number of cycles.
The factory default sets the Maintenance Alert Trigger to 10,000 cycles.
The Maintenance Alert Trigger can be programmed for 5, 10, 15, or 25
thousand cycles.
The Maintenance Cycle Count can be reset independently from the
operator’s absolute Cycle Count.
Mid-travel Stop Position
The Controller can be programmed so the gate will stop at a mid-travel
point instead of fully opening. This can be useful in installations where a
large gate, that takes a long time to open and close fully, only needs to
be opened partway to allow traffi c to pass.
The factory default sets the Controller for full open operation. Alternately,
the Controller can be programmed to open for 1 to 99 seconds then stop,
before reaching the open limit.
When a Mid-travel Stop Position time has been programmed, the gate
will
still fully open
if the Fire Department input is triggered, if the
OPEN
button is held down beyond the Mid-travel Stop Position, or a close
obstruction or reverse loop input is triggered.
✓
NOTE:
The Mid-travel Stop feature is disabled when dual gate
operation is enabled for paired units.
Anti-tailgate Enable
The factory default sets the Anti-tailgate Enable to OFF. With this setting,
during a gate cycle, after the shadow loop has been triggered by the
vehicle and then has cleared after the vehicle passes, the Auto Close
Timer or a CLOSE command is required to begin closing the gate.
If the Anti-tailgate Enable is set to ON, the gate will close immediately
as soon as the shadow loop has cleared. Any subsequent shadow loop
triggers while the gate is closing will stop the gate. When the shadow loop
clears, the gate will continue closing.
Radio Enable
The Controller contains a built-in MegaCode
®
radio receiver to allow
activation from up to 40 access control transmitters and two Model MGT
(gate edge) transmitters. The factory default enables the internal radio
receiver. Alternately, the internal receiver can be disabled.
Antenna Installation
The Controller is supplied with a local whip antenna installed. If using a
remote antenna, remove the whip antenna and connect coax cable from
the antenna to the
ANTENNA
connector.
FUNCTION
S
ET
S
THI
S
MAINTENANCE ALE
R
T T
R
I
GG
E
R
FO
R
5, 10, 15, O
R
2
5 THOU
S
AND CYCLE
S
DI
S
A
B
LE
S
THE MAINTENANCE ALE
R
T
FUNCTION
R
E
S
ET
S
THE MAINTENANCE ALE
R
T
INDICATO
R
AND
S
ET
S
THE MAINTENANCE
ALE
R
T COUNT TO ZE
R
O
OPTIONS
P
R
E
SS
UP O
R
DOWN TO CYCLE
TH
R
OU
G
H OPTION
S
P
R
E
SS
ENTE
R
TO
S
ELECT AN OPTION
MAINTENANCE
ALERT TRIGGER
"MA"
FUNCTION
P
R
E
SS
ENTE
R
TO
S
TA
R
T THE CYCLE COUNT DI
S
PLAY
1ST DISPLAY
NOTE
:
PRESS ENTER FOR 2 SECONDS
WHILE THE "CT" FUNCTION IS DISPLAYED
TO RESET THE CYCLE COUNT TO ZERO
RESET CYCLE
COUNT
"CT"
2ND DISPLAY
3RD DISPLAY
4TH DISPLAY
EXAMPLE A
B
OVE
S
HOW
S
10,4
2
0 CYCLE
S
DECIMAL POINT LIT
ON 4TH DI
S
PLAY
FUNCTION
S
ET LEN
G
TH OF OPENIN
G
TIME
F
R
OM 1 TO
99
S
ECOND
S
MID-T
R
AVEL
S
TOP DI
S
A
B
LED
(
G
ATE
R
UN
S
FULL T
R
AVEL)
OPTIONS
P
R
E
SS
UP O
R
DOWN TO CYCLE
TH
R
OU
G
H OPTION
S
P
R
E
SS
ENTE
R
TO
S
ELECT AN OPTION
MID-TRAVEL
STOP POSITION
"MT"
FUNCTION
ANTI-TAIL
G
ATE ENA
B
LE OFF
G
ATE
R
EQUI
R
E
S
AUTO O
R
MANUAL CLO
S
E
OPTIONS
P
R
E
SS
UP O
R
DOWN TO CYCLE
TH
R
OU
G
H OPTION
S
P
R
E
SS
ENTE
R
TO
S
ELECT AN OPTION
ANTI-TAILGATE
ENABLE
"AT"
ANTI-TAIL
G
ATE ENA
B
LE ON
G
ATE CLO
S
E
S
WHEN
S
HADOW LOOP CLEA
RS
FUNCTION
INTE
R
NAL
R
ADIO
R
ECEIVE
R
DI
S
A
B
LED
OPTIONS
P
R
E
SS
UP O
R
DOWN TO CYCLE
TH
R
OU
G
H OPTION
S
P
R
E
SS
ENTE
R
TO
S
ELECT AN OPTION
RADIO
ENABLE
"RA"
INTE
R
NAL
R
ADIO
R
ECEIVE
R
ENA
B
LED
