-39-
9.3 Specifications
Model
LE-270AR
LE-270GR
Interface
CAN: Comfort to ISO11898 standard. TJA1050LIN: Comfort to ISO9141 standard. TJA1021
Isolation
－
1kV galvanic isolation between USB connector / SD
card slot and measurement process section.
Connector
DSUB 25 pin male connector #4-40UNC
Number of Channels
2 channels of CAN or LIN, or 1 CAN and 1 LIN
Protocol
CAN, Device Net, LIN (Rev1.1, 1.2, 1.3, 2.0, 2.1)
Baud Rate
CAN: 125Kbps-1Mbps LIN: 400bps-26Kbps (arbitrary)
CAN Monitor
Standard/ Expansion format. Support bit timing settings.
LIN Monitor
Frame breaking is possible according to the data length of each ID or specified idle time.
Error Check
Break (LIN), Sync (LIN), Parity (LIN), Checksum (CAN/LIN), Framing (LIN)
Memory
PC: Max 32G byte on the HDD, PC-less: Capacity of the SD card supported by the analyzer(Specify
the file size from 128K /1M / 2M/ 4M / 8M / 16M / 32M byte
Mode
Remote mode (with PC); Data Logger mode (PC-less)
Measurement test mode
Online mode, Analog mode, Manual transmission mode
Measurement start/stop
Control from PC, Start/Stop switch, Auto-Power run, Specify date and time.
Time Stamp
“Hr:Min:Sec”, “Min:Sec:x1ms”, 9 digits: “100μs”, “10μs”, “1μs” (selectable)
*1
Filter
Record specific frames using Bit-mask ID, Bus ID (up to 8), Cut ID (up to 8).
Display on PC
Real-time display, Watch data display (display specified data of each ID), Analog data form display
Trigger
Condition
Data string up to 8 characters, specified remote frame (CAN), frame error (LIN), timer and counter,
logic status of external signal
Action
Stop measurement (offset can be set), validates/invalidates trigger condition, control timer/counter,
turn on/off the light of user-defined LED, output external signals, transmit CAN data (if using
Manual mode), start/stop capturing.
Retrieval function on PC
Trigger matched data, Error (Break, Sync, Parity, Checksum, Framing), Data: Specified ID (don’t
care available), Data string (Up to 8 characters; don’t care and bit mask available), CAN Remote
Data: Specified ID (don’t care available), Specified Time stamp, External signal
Conversion
Convert data into Text, CSV or KML format and save. OBD2 translation.
External Signal Input
Digital/Analog 4 channels Recording: At the time of receiving signals, or specified sampling cycle (1ms
- 10min, 13steps)Digital VIH 2V (Min.), VIL 0.5V (Max.)Analog Range: -15V to +15V, Accuracy:
±0.5%FS, A/D Max: 50Ksps, Resolution: 10bit
Acceleration data
－
Register and display the acceleration data of X/Y/
Z axis. The sensor KX022-1020-FR or equivalent is
built-in.
GPS positioning data
－
Register and display the latitude, longitude, above sea
level. SMA (femal) connector for active GPS antenna
is built-in.
LED
5 two-color LED: Power/Error, Test/Record, CH1/CH2, User-defined U1/U2, WiFi/GPS
*2
Switch
One: RUN / STOP
External Trigger Signal
1 Input, 2 Output (equipped in the measurement connector)
SD/SDHC Card
2 – 16Gbyte SD/SDHC
*3
2 – 32Gbyte SD/SDHC
*3
USB2.0 Port
Mini-B connector. High speed supported.
Wi-Fi Connection
*4
IEEE 802.11 b/g/n
Frequency range : 2400MHz-2483.5MHz
TX POWER: 802.11b: +20dBm 802.11g: +17dBm 802.11n: +14dBm
Power
USB bus power, DC-IN, or 1 pin of battery terminal of measurement connectorExternal DC power
(DC9-34V), AC adapter (6A-181WP09).
Power consumption
About 1.3W (1.9W when using Wi-Fi)
*5
About 1.7W (2.3W when using Wi-Fi)
*5
Run time during power
failure
Approx. 0.5sec
Ambient Temperature,
Humidity
In operation: -20-+60°C In storage: -20-+60°C, 20 - 85%RH (No condensation)
Dimension, mass
86(W)×130(D)×30(H) mm approx. 240g
Environment of PC
OS:Windows® 7/8.1/10
PC: PC/AT compatible
Accessories
PC software, Mini-USB cable, CAN/LIN Dsub cable, Power plug cable, 8G byte SDHC card
*1: Only “Hr:Min:Sec”, “Min:Sec:x1ms”is available on Analog mode.
*2: LE-270AR does not have GPS function.
*3: Only SD/SDHC cards sold or attached by LINEEYE are supported.
*4: Wi-Fi function is available only in Japan, USA, Canada, and EU nations where the product is needed to be compliant with RE
directive (2014/53/EU). The Wi-Fi function of this product is set to invalid depending on the country where it is shipped.
Please contact LINEEYE for the detail.
*5: The maximum is 2.7W for about 10 seconds after turning on the power.
